OpenMANIPULATOR-X (RM-X52-TNM) teardown: parts and sources
The 37 parts inside OpenMANIPULATOR-X (RM-X52-TNM): OpenCR1.0, STM32F746ZGT6, AL422B, D435, D435i, OV7725. Maker and distributor stock for each, with the source document…
ROBOTIS · RM-X52-TNM
| Part | Maker | Use | Source |
|---|---|---|---|
| OpenCR1.0 | ROBOTIS | Controls the arm through Arduino | |
| STM32F746ZGT6 | Runs control firmware and processes robot commands | ||
| AL422B | Buffers camera frames before OpenCR processes them. | ||
| D435 | Intel RealSense | Provides RGB and depth data for manipulator perception. | |
| D435i | Intel RealSense | Provides RGB and depth data for manipulator perception. | |
| OV7725 | Supplies camera data to the OpenCR board. | ||
| AS5045 | ams | Measures joint rotation and provides absolute angle feedback | LCSC C38892690 |
| MPU9250 | Measures tri-axis acceleration, angular rate and magnetic field | ||
| DC12-P-BEARING | Supports idler rotation and reduces friction | ||
| HN12-I101 | Connects the gripper to its actuator | ||
| X430 | DYNAMIXEL | Provides powered joints for the arm and gripper. | |
| XH430 | DYNAMIXEL | Provides powered joints for the arm and gripper. | |
| XH430-V-series | Provides 24 V-powered joints for the arm. | ||
| XL430 | DYNAMIXEL | Provides powered joints for the arm and gripper. | |
| XM430 | DYNAMIXEL | Provides powered joints for the arm and gripper. | |
| XM430-W350 | ROBOTIS | Drives manipulator joints with position and velocity control | |
| XM430-W350-T | DYNAMIXEL | Drives arm joints and gripper | |
| 20010WS-02 | Provides a 3.3V power output | ||
| PS-10 | ROBOTIS | Provides 12V 5A power to the arm | |
| SMPS 12V5A | Provides 12-volt, 5-ampere power | ||
| SMW250-02 | Converts external supply to 12V output | ||
| 20010WS-04 | Provides UART and CAN communication interfaces | ||
| B3B-EH-A | Connects TTL to DYNAMIXEL actuators | ||
| B4B-EH-A | Connects RS-485 to DYNAMIXEL actuators | ||
| CABLE-X3P-100 | Connects the controller and actuator | ||
| CABLE-X3P-180 | Connects the controller and actuator | ||
| CABLE-X3P-240 | Connects the controller and actuator | ||
| ROBOT Cable-X3P 100mm | Connects U2D2 to three-pin TTL devices | ||
| ROBOT Cable-X3P 180mm(Convertible) | Converts Molex and JST connectors for DYNAMIXEL connections | ||
| ROBOT Cable-X4P 100mm | Connects U2D2 to four-pin RS-485 devices | ||
| ROBOT Cable-X4P 180mm(Convertible) | Converts Molex and JST connectors for DYNAMIXEL connections | ||
| U2D2 | Converts USB commands to the actuator bus | ||
| Base Plate-02 | ROBOTIS | Provides the robot base mounting plate | |
| FR12-H101K | Forms the arm and gripper frame | ||
| FR12-H104K | Forms the arm and gripper frame | ||
| FR12-S101K | Forms the arm and gripper frame | ||
| FR12-S102K | Forms the arm and gripper frame |