Thor open-source 3D-printed 6-DoF robot arm · A 6-DoF 3D-printed arm in the yaw-roll-roll-yaw-roll-yaw configuration most industrial arms use: seven NEMA 17 steppers (three with 5:1 reduction for joints 2 and 3) with 3D-printed gears, GT2 belts and a semi-differential wrist, and an MG995 servo for the gripper; the README gives 625 mm stretched height (without end effector) and a 750 g maximum payload (end effector included), and the creator's drawing gives a 202 mm base and axis spacings of 160 mm, 195 mm and 67.15 mm (about 422 mm from shoulder axis to tool flange)
A 6-DoF 3D-printed arm in the yaw-roll-roll-yaw-roll-yaw configuration most industrial arms use: seven NEMA 17 steppers (three with 5:1 reduction for joints 2 …
- Maker
- Ángel L.M. (AngelLM) open-source project
- Form
- A 6-DoF 3D-printed arm in the yaw-roll-roll-yaw-roll-yaw configuration most industrial arms use: seven NEMA 17 steppers (three with 5:1 reduction for joints 2 and 3) with 3D-printed gears, GT2 belts and a semi-differential wrist, and an MG995 servo for the gripper; the README gives 625 mm stretched height (without end effector) and a 750 g maximum payload (end effector included), and the creator's drawing gives a 202 mm base and axis spacings of 160 mm, 195 mm and 67.15 mm (about 422 mm from shoulder axis to tool flange)
- For
- The site says the main purpose was a robot for teaching robotics in universities and schools, and the README calls it ideal for educational settings, makers and robotics enthusiasts; the FAQ warns it is a long project that may take weeks or months
- Sensors
- The BOM has no camera or microphone; homing uses 4 optical endstops and a micro endstop (printed discs block the light except at a slot)
- Connectivity and app
- Controlled with G-code: an Arduino Mega with the home-made Thor ControlPCB (based on RAMPS 1.4, with 8 A4988 drivers) runs GRBL 0.9j “Thor Version 1.0” over USB serial at 115200 baud; a commercial Fly Super8 Pro H723 board running RepRapFirmware 3.5.4 also works. On the PC side there is Asgard (PyQt5) or Thor-ROS (ROS 2 Humble and MoveIt2, with a React web version of Asgard, on Ubuntu 22.04 or Windows 11 with WSL2). No mobile app and no cloud service
- Subscription
- Open-source project, no subscription
- Openness
- The Thor repo (FreeCAD sources, STLs, STEPs and mods) is CC BY‑SA 4.0 (GitHub API and README); Thor-ROS and Asgard are also CC BY‑SA 4.0; the Fly Super8Pro config repo is Apache‑2.0; the firmware is a GRBL fork that GitHub reports as NOASSERTION, whose COPYING file says GPLv3 or later. The Thor ControlPCB repo holds KiCAD sources and Gerbers but no licence file (no licence declared), while the site says the schematics, sources and manufacturing files are released for download and modification
- Privacy
- No camera or microphone and no cloud service; the control software runs on a local PC.
- Not stated
- Repeatability, weight, power-supply rating (the BOM lists only a DC jack), the creator's location, recommended age
Vendor claims
- An open-source, 3D-printed 6-DoF arm, affordable and accessible, ideal for educational settings, makers and robotics enthusiasts, with success cases in school and university robotics courses already (README)
- Hardware cost below €350 (not counting a 3D printer)
- Designed with open-source tools only (FreeCAD, KiCAD, GRBL), controlled with G-code like 3D printers and CNCs, with ROS 2 integration
Parts
- Atmega328p · Executes the Grbl motion-control firmware
Sources
- github.com/AngelLM/Thor
- github.com/AngelLM/Thor/blob/main/README.md
- github.com/AngelLM/Thor/blob/main/LICENSE
- github.com/AngelLM/Thor/blob/main/doc/ThorDimensions.png
- github.com/AngelLM/Thor/releases
- github.com/AngelLM/Thor-ROS
- github.com/AngelLM/Asgard
- github.com/AngelLM/ThorControlPCB
- github.com/AngelLM/grbl
- github.com/AngelLM/Thor-Fly-Super8Pro-config