Connecting to sources…

Faze4 3D-printed 6-axis arm with cycloidal gearboxes · A 6-axis 3D-printed arm styled after FANUC's LR Mate 200iD: six steppers (three NEMA 23, two NEMA 17 and one NEMA 14 with a 19:1 planetary gearbox), 3D-printed cycloidal reducers (11:1, 15:1, 27:1) plus belts on joints 1–5, and every wire hidden inside the arm; the official video description gives a 70 cm reach and about 15 kg, the docs say 14–15 kg (less with lower infill), and the link lengths are L1 236.82 mm, L2 320 mm, L3 73.5 mm, L4 250.7 mm and L5 57 mm; no payload is given

A 6-axis 3D-printed arm styled after FANUC's LR Mate 200iD: six steppers (three NEMA 23, two NEMA 17 and one NEMA 14 with a 19:1 planetary gearbox), 3D-printed…

Maker
Petar Crnjak (Source Robotics, Zagreb, Croatia)
Form
A 6-axis 3D-printed arm styled after FANUC's LR Mate 200iD: six steppers (three NEMA 23, two NEMA 17 and one NEMA 14 with a 19:1 planetary gearbox), 3D-printed cycloidal reducers (11:1, 15:1, 27:1) plus belts on joints 1–5, and every wire hidden inside the arm; the official video description gives a 70 cm reach and about 15 kg, the docs say 14–15 kg (less with lower infill), and the link lengths are L1 236.82 mm, L2 320 mm, L3 73.5 mm, L4 250.7 mm and L5 57 mm; no payload is given
For
The README says it is aimed at research, education and anyone who wants to make their own robot arm; the Source Robotics blog says it is mostly used by students for thesis work and as a DIY project, with most users taking only the mechanics and adding their own software and electronics
Sensors
The BOM has no camera or microphone; joints 1 and 6 home on inductive sensors and the others on limit switches (Hackaday), and the V2 distribution board's sensor inputs are 24V and optocoupler-isolated. No joint encoders are described; the steppers run open loop
Connectivity and app
Low-level control runs on a Teensy 3.5 wired through the Faze4 V2 distribution board to the stepper drivers (the docs follow the TB6600 pinout), limit switches and an OLED display, with separate 24V and 5V inputs; inverse kinematics, trajectory planning and simulation run on a PC in Matlab (R2018a with Peter Corke's Robotics Toolbox 10.3.1), with ROS example code too. No app and no cloud service
Subscription
Open-source project, no subscription
Openness
The licence is stated inconsistently: the repo's LICENSE file has been CERN-OHL-S-2.0 (strongly reciprocal open hardware, also what the GitHub API reports) since 2025‑09‑24, replacing a 2019 LICENSE, while the README badge and last line still say MIT and the official store page also calls the software and STLs MIT. The repo holds the STLs (STL_V2.zip), the cycloidal-disc STEPs, the assembly PDF, the BOM, the V2 distribution board's schematic and board files, a URDF and Matlab and Teensy code; the full set of per-part STEP files is not open and is sold for €23 on the official store, which says they should not be shared without permission
Privacy
No camera or microphone and no cloud service; the control code runs on a local Teensy and PC.
Not stated
Payload, repeatability, the exact stepper driver and power supply (the docs say any driver with enough current will do), BOM prices (the sheet lists none), print time, assembly time, recommended age

Vendor claims

  • Functionally and aesthetically similar to industrial arms, aimed at research, education and anyone who wants to make their own robot arm (README)
  • Cheap: under $1,000 for the whole arm (README and official video); the docs put the total at about $1,000–1,500
  • 3D-printed cycloidal gearboxes with low backlash that are easy to repair, and every wire hidden for a clean design (README)

Parts

  • STM32 Blue Pill · Runs a serial stepper controller test
  • Teensy 3.5 · Executes the arm's low-level control
  • teesny 3.5 · Runs low-level control for the arm
  • TB6600 · Drives stepper motors and controls arm joints
Parts and sources

Sources