Connecting to sources…

How to build PingTi Arm (low-cost human-arm-scale robot arm): the whole process

66 steps to build PingTi Arm (low-cost human-arm-scale robot arm), from buying parts, printing and assembly to software, calibration and training, with the bill of mater…

The creator's BOM estimate in the README: about $261 for one arm (the English table totals $261.09 / €218.28) and about $390 for a pair with an SO‑100 leader; the Chinese table totals CN¥1,719.1 for one arm (the Chinese README says about CN¥1,800, or CN¥2,486 for a pair). Upgrading an SO‑100 follower that already uses 12V 30 kg·cm servos costs about $157 (CN¥973). The English table leaves out a power supply and USB cable (the Chinese one includes a 12V 5A supply), and neither includes filament, screws or shipping; the creator says prices are for reference only. There is no official kit price

Bill of materials · Parts For PingTi Arm

PartQtyUSEU
STS3250 Servo2USD 73.89
STS3215 Servo (12V,30 kg.cm)6USD 13.89
Motor Control Board1USD 7.05
Table Clamp 2pcs1USD 9
Dupont Wire1USD 6.98

Bill of materials · Parts for SO100 Leader Arm

PartQtyUSEU
STS3215 Servo (7.V, 20kg.cm)6USD 14
Motor Control Board1USD 11
USB-C Cable 2 pcs1USD 7
Power Supply1USD 10
Table Clamp 2pcs1USD 9
Screwdriver Set1USD 6

Buy parts

  • Select the teleoperation arms

    Use the PingTi Arm as the follower and the SO100 Arm as the leader, then purchase the components listed for both in the BOM.

  • Purchase PingTi components

    Purchase the seven components listed in the PingTi Arm BOM using the stated specifications and purchase links.

  • Purchase SO100 components

    Purchase the seven components listed in the SO100 leader-arm BOM using the stated specifications and purchase links.

  • Budget using reference prices

    Treat the BOM prices as reference prices because actual prices may change with market fluctuations.

  • Choose equivalent replacement parts

    Use the listed links for the servos and USB driver board; the other components may be purchased from other sellers in the same specifications.

  • Select the Feetech USB driver board

    Do not use the previously recommended Waveshare USB Drive board because it cannot drive the PingTi Arm’s eight servos; use the Feetech USB Drive board instead.

  • Buy parts for one arm
  • Choose Feetech USB drive board

    The Waveshare USB Drive board recommended by the SO-100 team could not drive all eight servos of the PingTi Arm, so the Feetech USB Drive board is used; components other than servo motors may be bought as equivalent products.

  • Skip extra board for SO-ARM101

    If you modify an SO-ARM101 kit that comes with a Seeed Studio XIAO servo driver board, you do not have to buy the additional motor board, as it is also capable of driving a PingTi Arm.

  • Buy SO-100 leader arm parts

    The SO-100 leader arm BOM is copied from the SO-100 repo; the PingTi arm can serve as the follower arm in teleoperation tasks while the SO-100 arm is the leader.

  • Buy the Parts Needed to Extend PingTi Arm

    After assembling SO-100 with `12V 30KG.cm` servos, buy 2 more servos and 1 more USB control board to expand it into PingTi Arm.

Print and make

  • Download PingTi arm STL files

    Obtain the STL files for the 3D-printed parts from the `../stl_3d_printing/` directory.

  • Print parts with specified settings

    Set the layer height to 0.2 mm, initial layer height to 0.2 mm, sparse infill density to 13%, and enable support. Printing the parts takes an estimated time of about 20 hours.

  • Prepare optional alternate links

    `elbow_link_alternate` and `shoulder_link_alternate` can replace the usual elbow and shoulder links. They are slightly shortened, can be printed horizontally on a Bambu A1 print bed, and mimic the SO-ARM101 design.

  • Increase Link Infill for Heavy Payloads

    If you will frequently use the arm with heavy payloads, increase the infill density when printing the links.

Assemble

  • Place the 8 servos

    Place 2 ST-3250 (50kg.cm) servos and 6 ST-3215 (30kg.cm) servos as shown in the image.

  • Place the 10 links

    Place all 10 links as shown in the image.

  • Connect the USB drive board

    Connect the power supply and servos as shown in the Feetech USB Drive Board image. Although the V1 port is labeled DC6V-9V, Feetech tech support confirmed that a 12V power supply can be safely connected.

  • Add motor horns to all 8 servos

    Refer to the LeRobot official video to add motor horns to all 8 servos.

  • Assemble base links with servo 1

    Watch Step4.1 through Step4.4 of the SO-100 assembly video to assemble the base links with servo ID 1.

  • Connect shoulder servo wires

    The shoulder joint has 2 ST-3250 servos. Connect all 4 wires on each servo before placing the servos in their slots.

  • Install shoulder servos

    Place servo ID 2 in the left slot and servo ID 3 in the right slot. Secure the servos with four M2x5 screws.

  • Attach shoulder link to horns

    Attach the shoulder link to the servo horns using 8 M3x6 machine screws. The shoulder link should be vertical, with the servo horns on its end facing forward.

  • Connect elbow servo wires

    The elbow joint has 2 ST-3215 servos with IDs 4 and 5. Connect the wires properly before placing the servos in their slots.

  • Install elbow servos and link

    Place servo IDs 4 and 5 in their servo slots and secure them using four M2x5 screws. Attach the elbow link to the servo horns using 8 M3x6 machine screws.

  • Assemble the Wrist and Gripper

    Follow the SO-100 assembly video from Step 4.9 to Step 4.12 to assemble the wrist links, gripper links, and servos. Use servos with IDs 6, 7, and 8.

  • Place the eight servos

    Place the two ST-3250 servos and six ST-3215 servos according to the servo placement diagram.

  • Place the ten linkages

    Place the ten linkages according to the linkage placement diagram.

  • Connect the USB board

    Connect the power supply, servos, and Feetech USB driver board as shown in the image. The V1 port is marked DC6V-9V, but Feetech technical support confirmed that a 12V supply is safe.

  • Install horns on eight servos

    Install the motor horns on all eight servos using the official LeRobot video.

  • Assemble the base link

    Use the SO-100 assembly video to assemble the base link with servo ID 1. Follow Steps 4.1 through 4.4 in the video.

  • Connect Shoulder servo cables

    Connect all four cables before placing the two servos in their slots.

  • Install Shoulder servos

    Place ID 2 in the left slot and ID 3 in the right slot of base_yaw_link, then secure them with four M2x5 screws.

  • Connect Shoulder link

    Use eight M3x6 machine screws to connect the Shoulder link to the servo horn. The link must be perpendicular, with its end servo slot facing forward.

  • Connect Elbow servo cables

    The Elbow joint uses two ST-3215 servos with IDs 4 and 5. Connect the cables correctly before placing them in their slots.

  • Install Elbow servos and link

    Place ID4 in the left slot and ID5 in the right slot, then secure them with four M2x5 screws. Connect the Elbow link to the servo horn using eight M3x6 machine screws.

  • Assemble Wrist and Gripper

    Use the SO-100 assembly video to assemble the wrist link, gripper link, and servos with IDs 6, 7, and 8. Start at step 4.9 and continue through step 4.12.

Software

  • Create an environment with venv

    Create a `.venv` virtual environment with Python 3.12, activate it, and upgrade pip.

  • Create an environment with conda

    Create a conda environment named `pingti_lerobot` with Python 3.12, activate it, and upgrade pip.

  • Clone the bridge repository

    Move to the parent workspace directory, then clone the `pingti_lerobot_bridge` repository.

  • Install the bridge package

    Enter the repository directory and install the package; it installs `lerobot[async,feetech,transformers-dep]==0.5.1` from PyPI.

  • Confirm the v4 joint set

    Confirm that the v4 URDF contains five arm joints and one gripper joint. Its transforms already include the agreed nominal zeros and axis directions: the base, shoulder, elbow and wrist pitch use CAD travel midpoints, while wrist roll uses the copied SO ARM wrist reference geometry.

  • Enable LeRobot degree mode

    Configure PingTi in LeRobot with `use_degrees=True`.

  • Choose joint or observation key names

    Provide the five joint names to the mapping, or use observation keys such as `shoulder_pan.pos`.

  • Install LeRobot and find USB ports

    Install the library using the “Install LeRobot” section of the official LeRobot tutorial, and find the USB ports using the “Find the USB ports associated to each arm” instructions. The Feetech USB board port number may occasionally change; if a “port not found” error occurs, recheck the USB port.

  • Install LeRobot and find USB ports

    Install the LeRobot library using the official LeRobot tutorial. Follow the official tutorial to find the USB ports associated with each arm.

Calibrate and test

  • Identify both control board ports

    Identify the port numbers of the PingTi Arm and SO-ARM100 control boards using the linked LeRobot port-finding tutorial.

  • Calibrate the SO100 Leader

    Run the calibration command following the LeRobot SO100 Leader calibration guide.

  • Calibrate the Pingti Follower

    Run the calibration command and replace the port number with the port number of your PingTi Arm.

  • Move the PingTi arm joints

    Move the joints of the PingTi arm in a similar way to the linked SO101 calibration video.

  • Select the lower-torque shoulder variant

    For the lower-torque shoulder variant, use `--robot.type=pingti_lite_follower` instead of the follower type.

  • Set the first servo ID to 1

    Run the configuration script to set the first servo's ID to 1 and its position to 2048.

  • Set the second servo ID to 2

    Unplug the first servo, connect the second servo, which should be an ST3250, and set its ID to 2. Both model types share the same SDK and control table, so `--model sts3215` can still be used.

  • Configure all motors through ID 8

    Repeat the process for all motors until ID 8. The two ST-3250 servos should have IDs 2 and 3; refer to the servo placement drawing for reference.

  • Configure motor ID 1

    Run the configuration script to set the servo ID to 1 and the servo position to 2048.

  • Configure second ST-3250 motor

    Unplug the first servo, connect the second ST-3250 servo, and set its ID to 2. Both models share the same SDK and control table, so continue using the --model sts3215 argument.

  • Set all eight motor IDs

    Repeat the configuration process until all eight servo IDs are set. The two ST-3250 servos should have IDs 2 and 3; refer to the servo placement diagram.

  • Avoid duplicate CAD corrections

    Do not apply the CAD offsets or signs again because the URDF transforms already include them. The mapping itself does not connect to the robot or establish physical calibration.

  • Measure motor directions and TCP

    Treat `tool_mount_link` as the output-horn reference frame, not a measured gripper TCP. Measure physical motor directions, repeatable endpoints and TCP before Cartesian control.

Data and training

  • Run teleoperation

    Run teleoperation using the documented command and replace the port with your own port.

  • Run teleoperation with camera

    Run teleoperation with the camera command to check whether the camera captures the teleoperation scene properly before collecting a dataset.

  • Record and visualize dataset

    Record the dataset by following the Data Record Guideline.

  • Train and evaluate policies

    Train and evaluate policies by following the linked Lerobot Tutorial.

  • Run async inference

    Run asynchronous inference on the robot server using the documented command.

  • Start robot client to run the act model

Use it

  • Avoid Sudden Movement Under Heavy Load

    Avoid sudden movement and stopping while carrying a heavy payload such as 500g, because the shoulder joint may be damaged.

Common problems

  • New LeRobot releases removed configure_motor.py, preventing motor ID setup #3
  • URDF definitions break simulator imports and PhysX operation in Blender and Isaac Lab #1 #6

Parts

  • 2 Feetech STS3250 servos (12V, 50 kg·cm, shoulder IDs 2 and 3, $73.89 each in the English table)
  • 6 Feetech STS3215 servos (12V, 30 kg·cm: base ID 1, elbow IDs 4–5, wrist and gripper IDs 6–8, $13.89 each)
  • Feetech FE-URT-1 USB bus servo board ($7.05); the Chinese table adds a 12V 5A power supply
  • 2 table clamps and jumper wires; M2×5 and M3×6 screws (assembly tutorial)
  • 10 printed links from 12 STLs, 7 of them taken from the SO‑100 (base, wrist, gripper), plus shortened shoulder and elbow links that print flat
  • Leader (optional): an SO‑100 leader with 6 7.4V STS3215 servos, a Waveshare driver board, USB‑C cable and power supply

Tools

  • A 3D printer (the creator printed PETG on a Bambu Lab A1): 0.2 mm layers, 13% infill, supports on; raise the infill for frequent heavy payloads
  • A screwdriver (the SO‑100 leader BOM lists a screwdriver set)

Skills

  • Setting the ID and middle position of all 8 servos one by one with LeRobot's script (the STS3250s are configured as sts3215 too)
  • Following the SO‑100 assembly video for the base, wrist and gripper, and the repo's photos for the twin-servo shoulder and elbow
  • Python 3.12 and LeRobot: lerobot-calibrate, lerobot-teleoperate, dataset recording and policy training

Software

  • pingti_lerobot_bridge (Apache‑2.0): pip install . pulls in lerobot 0.5.1, with robot types pingti_follower / pingti_lite_follower and an so100_leader
  • A v4 URDF (loads in PyBullet) with joint_mapping.py; the Fusion 360 assembly is editable
  • The creator's SmolVLA fruit-picking training dataset on Hugging Face, zhenxuan/PingTi-OrchardPick-Jujube

Documents