How to build Otto (Otto DIY / HP Robots Otto): the whole process
54 steps to build Otto (Otto DIY / HP Robots Otto), from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop link…
HP Robots Otto Starter Builder Kit $161.20 (RobotShop US, 2026‑10‑25, before tax and shipping); HP shows no price and the original DIY BOM cost is not stated
Buy parts
- Choose a modular expansion kit
Use modular expansions to add more ways to build and code the robot.
- Choose the Sense expansion kit
The Sense expansion kit is for understanding the environment.
- Choose the Interact expansion kit
The Interact expansion kit is for control and input.
- Choose the Emote expansion kit
The Emote expansion kit adds more personality to the robot.
- Choose the Invent expansion kit
The Invent expansion kit supports multiple walking mechanisms and is compatible with third-party electronics.
Assemble
- Assemble the robot using the manual
Assemble the robot using the detailed and enjoyable manual.
- Connect the battery and wire components
Connect the battery and wire the components to the circuit board.
- Swap in the OLED display
Swap to an OLED screen to display faces, data, messages, numbers, games, and more.
Software
- Install the Arduino IDE
Install the Arduino IDE on your computer.
- Find the OttoDIYLib library
Find the `OttoDIYLib` library by Otto DIY in Arduino Manager for quick installation, or install it manually using the steps below.
- Download the Otto DIY libraries
Download the Otto DIY libraries ZIP file.
- Open the Add ZIP Library menu
Open the Arduino IDE and navigate to Sketch > Include Library > Add .ZIP Library.
- Select and open the ZIP file
Navigate to the location of the downloaded ZIP file and open it.
- Check the installation message
Check the message in the black area at the bottom of the IDE to confirm that the library has been installed.
- Verify the library installation
Open the Sketch > Include Library menu and confirm that the library appears at the bottom of the drop-down menu.
- Open the OttoDIYLib examples
Open File > Examples > OttoDIYLib in the Arduino IDE to view the example codes provided by the library.
- Test all movements sounds and gestures
Run `Otto_allmoves.ino` to test all dance movements, sounds and gestures.
- Run the Bluetooth app example
Use `Otto_APP.ino` with the Bluetooth mobile app and module.
- Run the touch modes example
Use `Otto_touchmodes.ino` to demonstrate multiple modes with a touch sensor or button.
- Run the ultrasonic obstacle example
Run `Otto_avoid.ino` to use the ultrasonic sensor to avoid obstacles.
- Run the servo calibration example
Run `Otto_CalibrationWalk.ino` for simple servo calibration.
- Run the birthday melody example
Run `Otto_happybirthday.ino` to play a melody.
- Run the song dance example
Run `Otto_singleladies.ino` to make the robot dance according to the song.
- Run another song dance example
Run `Otto_smoothcriminal.ino` to make the robot dance according to the song.
- Test an analog sensor
Run `Otto_testSensor.ino` to read data from any analog sensor.
- Test the light sensor
Run `Otto_photoresistor.ino` to test the light sensor.
- Add the Otto library
Include Otto.h in the program and create an instance named Otto.
- Declare servo and buzzer pins
Set the default signal pins for AVR Arduino boards: left leg 2, right leg 3, left foot 4, right foot 5, and buzzer 13; other pins can be used by also changing their numbers in the code.
- Program the robot to come alive
Make the robot come alive with code and add your own personality.
Calibrate and test
- Initialize and home the servos
In setup, call init with the four servo pins, servo motor calibration parameter true, and buzzer pin; then call home so Otto stands in the neutral position with the servos centered.
Use it
- Adjust movement parameters
Change the function parameters to alter the speed, direction, and size of movements.
- Make Otto walk
steps is the number of repetitions, and time is the movement duration in milliseconds; a higher value slows the movement, with values from 500 to 3000 recommended. Use dir 1 to walk forward or -1 to walk backward.
- Make Otto turn
Set the number of turn repetitions, duration T, and direction; 1 turns left and -1 turns right.
- Make Otto bend
Set the number of bend repetitions, duration T, and direction; 1 bends left and -1 bends right.
- Make Otto shake its leg
Set the number of leg-shaking repetitions, duration T, and direction; 1 shakes left and -1 shakes right.
- Make Otto jump
Set the number of upward jumps and duration T; jump has no direction parameter.
- Perform the moonwalker dance
Set the steps, duration T, movement height or size h, and direction; 1 moves left and -1 moves right. Adjust h between 15 and 40.
- Perform the Crusaito dance
Set the steps, duration T, movement height or size h, and direction; 1 moves left and -1 moves right. Adjust h between 20 and 50.
- Perform the flapping movement
Set the steps, duration T, movement height or size h, and direction; 1 moves front and -1 moves back. Adjust h between 10 and 30.
- Perform the swing movement
Set the steps, duration T, and movement height or size h; adjust h between 0 and 50.
- Perform the tiptoe swing
Set the steps, duration T, and movement height or size h; adjust h between 0 and 50.
- Perform the jitter movement
Set the steps, duration T, and movement height or size h; adjust h between 5 and 25.
- Perform the up-down movement
Set the steps, duration T, and movement height or size h; adjust h between 0 and 90.
- Perform the ascending turn
Set the steps, duration T, and movement height or size h; adjust h between 5 and 15.
- React to noises and claps
Use the microphone so Otto reacts to noises and claps.
- Measure temperature and humidity
Use Climate Duo to let Otto measure environmental temperature and humidity.
- Detect environmental light levels
Use the light sensor to detect and measure light from natural sunlight or flashlights.
- Detect rotation and shaking
Use the tilt sensor to detect rotation on the robot and movement when it is shaken.
- Execute commands with a button
Push the button to execute quick commands.
- Precisely adjust levels and speed
Use the potentiometer to precisely adjust brightness, speed levels, and more.
- Fine-tune values with rotary steps
Use the encoder with button for precise step rotation when fine-tuning multiple variables and codes.
- Measure acceleration for reactions and games
Use the accelerometer to measure robot acceleration for diverse reactions and engaging games.
- Display graphics with the LED matrix
Use the color LED matrix for RGB retro pixel graphics, emojis, mouths, light effects, and scrolling text.
- Control voice and music files
Use the MP3 player with integrated buttons and a switch for direct control of voice and music files.
Common problems
- Missing library headers or dependencies prevent sketches from compiling #5 #6
- Incompatible APIs and outdated examples cause compilation failures #10 #17 #23 #26 #30 #33
- Unsigned oscillator offsets break negative movement calculations on ESP32 #7 #16
- ESP32 sketches can trigger watchdog resets during operation #21
- Touch sensors start low in toggle mode, confusing programs #9
- Unvalidated EEPROM calibration data causes extreme leg positions #22
- Obstacle avoidance continues turning after detecting an obstacle #14
- Library functions lack sufficient documentation for independent builders #28
Parts
- HP board: Xtensa dual-core 32-bit LX6 at 240 MHz, 8 MB flash, 2.4 GHz Wi‑Fi, Bluetooth 4.2/BLE, 11 GPIOs on JST connectors
- Custom metal-gear servos (2.2 kg⋅cm continuous rotation)
- Ultrasonic sensor, IR line sensors, 13 RGB LEDs, 80 dB buzzer
- Replaceable 3.7V 1800 mAh battery (about 2 hours), USB‑C for charging and programming
- Original DIY: Arduino Nano and four leg servos (OttoDIYLib) in a 3D-printed shell
Tools
- The Builder kit includes plastic parts and tools; the Creator kit needs a 3D printer (HP page)
Skills
- Icon blocks → word blocks → Python (HP webcode)
- MicroPython (Thonny) or Arduino C++
Software
- HP webcode browser coding (no install, with electronics and game simulator)
- HP Otto app (iOS/Android) Bluetooth remote
- OttoDIYLib (Arduino)