Connecting to sources…

How to build ORCA Hand (orcahand v2)

15 steps to build ORCA Hand (orcahand v2), with the source documents.

Official BOM kits (orcahand.com, 2026‑11‑01, USD, shipping and import taxes extra): the full Dynamixel kit is $2,500; by group, servos + driver board + harness cost $1,800 (Dynamixel) or $1,000 (Feetech), printed parts $250, silicone skin $200 and mechanical parts $250. The official BOM sheet lists unit prices only, e.g. $103.39 per XC330-T288-T (16 needed) and $137.89 for the XC430-T240BB-T; the v1 paper puts material cost under CHF 2,000. Assembled hands start at $3,500

Print and make

  • Select the hand print files

    There are two hand variants, each with a hand print file and silicone skin mold print file. Download the `.3mf` project for the desired variant and open it in Bambu Lab Studio; the plates and print settings are already arranged.

  • Choose the actuator tower plate

    Choose the tower plate according to the actuators: use plate 1 `DYNAMIXEL` for Dynamixel or plate 2 `FEETECH` for Feetech. Only the tower differs; every other plate is the same for both actuator types.

  • Print the hand and TPU skins

    Print the hand itself, then print the finger skins and carpal skin on their separate `(TPU)` plates. The base hand uses white skins and the touch hand uses black skins; printing the skins directly in TPU is the quickest way to complete the hand.

  • Print the silicone molds

    Print the finger skin molds with their clips, carpal molds, and pouring funnels from `SiliconeMolds-*.3mf`. On the `WITH TPU (~85A)` plate, print the flexible carpal mold halves in soft TPU; print everything else in PLA.

  • Cast the silicone skins

    Cast the skins using the printed molds. The document recommends silicone skins because they grip better and last longer than TPU.

  • Use printed TPU skins instead

    For a quick temporary solution, use the TPU-printed skins from the hand print file. The document notes that silicone skins grip better and last longer than TPU.

  • Use compression molds instead

    If you prefer compression molding over pouring, use `orca_v2/base/07_Molds/Compression-Molds.3mf`. It contains compression molds for the finger and carpal skins.

  • Choose the correct variant files

    Use `SiliconeMolds-1100.3mf` for the base hand and `SiliconeMolds-2100.3mf` for the touch variant. Variant 3MFs resolve part names in their own variant folder first and then in `orca_v2/base/`; a variant's own copy of a name wins over base.

Assemble

  • Fit PTFE Tubes to Each Finger AP

    Insert one PTFE tube into each hole of the wide hole pair on every AP, leaving each tube about 1 mm proud on both sides.

  • Fit PTFE Tubes to the Carpals

    Insert a PTFE tube into each of the 32 carpal channels and trim them so they extend about 1 mm out on both sides.

  • Prepare the knotted tendon

    Tie a knot at one end of the tendon, then thread the tendon through the PTFE tube.

  • Thread the tendon through the channel

    Thread the tendon through the tight or winding channel.

  • Pull in the PTFE tube

    Pull the tendon from the other end of the channel to pull the PTFE tube into the channel instead of pushing it in.

  • Fit the PTFE tube over M4 screws

    Hold the tube tightly against the screw with one hand and use a screwdriver to screw it into the PTFE tube.

  • Secure a loose TPU carpal skin

    Check how the TPU-printed carpal skin fits into the carpals. It is unverified whether it fits as tightly as the silicone skin; glue it in if it is loose.

Common problems

  • CAD files conflict with the assembly video, making assembly unreliable #8
  • Required OrcaHand V2 URDF description is missing #8
  • Wrist bearing dimensions do not match the intended assembly #18
  • Finger motor model labels conflict between BOM and software #22
  • Packaged config inverts right-hand thumb and abduction motor directions #23

Parts

  • Dynamixel variant: 16 XC330-T288 (fingers, 0.92 N·m at 11.1V, 23 g) + 1 XC430-T240BB (wrist, 1.9 N·m at 12V), with a Dynamixel PowerBoard and U2D2
  • Feetech variant: 16 HL-2915 (1.39 N·m) + 1 HL-3930 (3.43 N·m) with an FE-URT-2 (USB‑C) board; both servo families share the mounting footprint and 4,096-step resolution
  • Tendons: about 24 m of 0.39 mm UHMWPE fishing line (6 m spare), touching only metal and PTFE tube; 55 4×8×3 bearings, a GT2 belt for the wrist, dowel pins and M2–M6 screws
  • Prints: PLA structure (Bambu Studio 3MF projects with a tower plate for each servo family); skins can be printed in TPU, but cast Dragon Skin 10 NV silicone from the molds is recommended
  • 12V 5A supply, two 50×50×10 mm fans, a USB‑C cable; a CNC aluminium arm connector plate (ISO 9409-1, fits UR, Franka Research 3/Panda, Kinova Gen3 and others)

Tools

  • A Bambu Lab printer (the official files are pre-arranged Bambu Studio projects), PLA and about 85A TPU; molds for casting the silicone skins (a compression-mold set is also provided)
  • CNC parts from a machining service (the repo notes FDM printing is not recommended); hand tools such as screwdrivers

Skills

  • Routing and tensioning tendons, following the assembly video and the ASSEMBLY_ADDENDUM notes
  • Python (uv or pip) and serial-port permissions; calibration with orca_core's tension, calibrate and neutral scripts
  • Advanced: MuJoCo/URDF simulation, teleoperation retargeting, imitation learning and sim-to-real reinforcement learning

Software

  • orca_core (MIT, latest tag v0.12.0): hardware abstraction, tensioning and calibration scripts, joint-space control
  • orcahand_description (MIT): MJCF and URDF models; orca_sim simulation environment (no licence declared)
  • orca_retargeter (MIT) and orca_teleop (no licence declared) for teleoperation; orca_ui (MIT) web tactile viewer

Documents