Connecting to sources…

How to build nanosaur (open-source NVIDIA Jetson dinosaur robot)

62 steps to build nanosaur (open-source NVIDIA Jetson dinosaur robot), with the source documents.

No kit is sold and the site gives no total. The BoM prices each part for the US, e.g. Pololu micro gearmotor $25.75, Adafruit motor driver $29.10, power bank $29.99, 5 GHz dongle $13.90, 64 GB microSD $9.99, Raspberry Pi Camera v2 $23.50, PLA $15 a spool, NinjaTek TPU $40; no Jetson price is listed. The first 5 expansion boards from PCBWay are free apart from shipping

Bill of materials · Table connectors

PartQty
USB 2.0 connector Plug A, Type Male 4 pin1
5m Flat ribbon cable 20P Rainbow IDC wire 1.27mm1
2Pin 2.54mm female Dupont connector1
3Pin 2.54mm female Dupont connector1
4Pin 2.54mm female Dupont connector2
2.54mm Dupont jumper wire cable15

Bill of materials · Screw set

PartQty
Hex M2 14mm1
Hex M2 6mm4
Hex M2 6mm4
Hex M2 10mm4
Hex M2 20mm6

Buy parts

  • Buy the required robot parts

    Purchase the listed components, including the NVIDIA Jetson, Pi camera, motors, and motor control.

  • Select a camera

    Available cameras are the Raspberry Camera v2, Stereolabs ZED mini, and Intel Realsense d435i.

  • Consider optional speed and assembly parts

    These optional parts are not required to build the robot, but are suggested to speed up the NVIDIA Jetson or assemble the robot.

  • Buy 3D printing filament

    Ninjatek TPU is suggested when using a Bowden 3D printer; otherwise, another type of TPU can be used.

  • Obtain the expansion board PCB

    First, obtain the nanosaur-expansion-board PCB.

  • Register a PCBWay account

    Register with PCBWay using the document’s referral link to support the project.

  • Open the nanosaur PCB project

    After registering, open the nanosaur project on PCBWay.

  • Add the PCB to the cart

    Click the “Add to Cart” button on the right.

  • Select and order the PCB quantity

    Keep all default settings and only select the number of PCBs wanted; the default minimum quantity is 5. The first order of five PCBs is free, so only shipping must be paid.

  • Buy a short M2 screw set

    nanosaur uses a short set of M2 screws, and you can buy a set.

Print and make

  • Download all Nanosaur STL files

    Download nanosaur-stl.zip; its 025in folder is for ball bearings sized ID 1/4in × OD 1/2in.

  • Configure the PLA print profile

    Split all parts following the guide and set the layer height to 0.2mm, print speed to 50mm/s, and infill to 15%.

  • Print the green PLA base rear

    Print the base rear part with green PLA; the average time is 5 hours.

  • Orient the base rear STL

    Orient the base rear STL as shown in the picture and disable supports.

  • Print the green PLA base front

    Print the base front part with green PLA; the average time is 1 hour and 30 minutes.

  • Print base front with tree supports

    Orient the base front STL as shown in the picture, enable supports, and set the support structure to Tree.

  • Print base front with build-plate-only supports

    Orient the base front STL as shown in the second picture, enable support material, enable supports on the build plate only, and disable bridging supports.

  • Choose the bearing files

    Open nanosaur-stl.zip and find the 025in folder for ball bearings with size ID 1/4in x OD 1/2in.

  • Print wheels and sprockets

    Print the wheels and sprockets with PLA green/black; the average time is 2 hours. Orient the STLs as shown, use auto arrange, and disable supports.

  • Print the sliders

    Print the sliders with PLA green; the average time is 2 hours. Follow the pictured orientations, use auto arrange, disable supports, and set Left to x=0 y=15 and Right to x=0 y=-15.

  • Print flap and power-bank holder

    Print the flap and power bank holder with PLA green; the average time is 1 hour and 45 minutes. Enable supports, set Support structure to Tree, and position flap_bottom.stl at x=20 y=0, flat_top.stl at x=-20 y=0, and pb_holder.stl at x=-55 y=0.

  • Block supports on holder and flap

    Follow the images and use the Paint-on supports tool to block all supports on the Power bank holder and Upper flap.

  • Configure final support generation

    Orient the STLs as shown and use auto arrange. Enable support material generation, enable support on build plate only, and disable support for bridges.

  • Select the camera cover

    Select the cover to print for the camera or stereo camera you use.

  • Print the fish-eye camera cover

    Use the linked 3D print instructions to print the cover for the fish-eye camera.

  • Print the Raspberry Cam V2 cover

    Use the linked 3D print instructions to print the cover for the Raspberry Cam V2.

  • Print the ZED Mini cover

    Use the linked 3D print instructions to print the cover for the ZED Mini.

  • Print the RealSense cover

    Use the linked 3D print instructions to print the cover for the RealSense camera.

  • Prepare track printing material

    A direct-drive 3D printer is preferred; otherwise use Ninjatek TPU, which is sufficiently elastic for the tracks.

  • Print the first track

    Orient the track STL as shown, with print speed at 30mm/s, infill at 10%, supports disabled, and retraction disabled.

  • Print the second track

    Orient the second track STL as shown, with print speed at 30mm/s, infill at 10%, supports disabled, and retraction disabled.

  • 3D Print nanosaur Gadgets

    3D print gadgets for nanosaur.

  • Set up and print all plastic parts

    Follow the linked 3D print page for setup and to print all 3D-printed parts.

Assemble

  • Pass screws through slider holes

    Pass all screws through all slider holes.

  • Install the wheel assembly

    Bring the wheel and assembly to the last housing following the picture below.

  • Fit the track to the sprocket

    Bring the track and fit it to the sprocket.

  • Fit the slider and wheel block

    Bring the slider and wheel block and fit the track to the wheel.

  • Screw all bolts

    Screw all bolts.

  • Route wires through the body

    Bring the Flap and pass all wires through the slot in front of the Body.

  • Assemble the Jetson Nano

    Assemble the NVIDIA Jetson Nano and screw all 4 M2 screws.

  • Orient the Adafruit power connector

    Direct the Adafruit power connector up.

  • Screw the motor controller

    Screw the motor controller.

  • Wire the motor controller

    Wire the motor controller following the wiring page.

  • Assemble the Flap on the Jetson Nano

    Assemble the Flap on the NVIDIA Jetson Nano connector.

  • Install the fish-eye camera

    Assemble the nanosaur head with the fish-eye camera cover, following the cover assembly instructions.

  • Install Raspberry Cam V2

    Assemble the nanosaur head with the Raspberry Cam V2 cover, following the cover assembly instructions.

  • Install ZED mini

    Assemble the nanosaur head with the ZED mini cover, following the cover assembly instructions.

  • Install the Realsense camera

    Assemble the nanosaur head with the Realsense camera cover, following the cover assembly instructions.

  • Complete the robot assembly

    This is the final step in building nanosaur; mount the head and the robot body.

  • Wire the two displays

    Wire the two displays using the cables from the Flap. The GND is on the left.

  • Wire the PI camera

    Wire the PI camera to the NVIDIA Jetson Nano.

  • Attach the head cover

    Clip the cover onto the nanosaur body.

  • Secure the cover with magnets

    Clip the cover onto the body. The magnets hold the cover without using any type of screw.

  • Assemble the power bank

    Slide the power bank into place as shown, clip the power bank holder, and plug the USB connector to the power bank.

  • Solder all XT connectors

    Solder all XT connectors following the assembly picture.

  • Solder power on the first row

    Solder the electronic power at the end of the first row.

  • Solder the second-row I2C connector

    Solder the I2C connector on the second row.

  • Identify motor polarity

    The rear motor cover has a “+” symbol that must be observed when soldering the motor wires.

  • Make the five labeled connections

    Make the connections using the listed labels: oled right, oled left, adafruit motor control, GPIO Pin 31, and GPIO Pin 33.

  • Assembly Without Magnets

    Assemble nanosaur by following the Assemby instructions and taking the extra steps for the body and head.

  • Assemble the nanosaur expansion board

    Assemble the nanosaur expansion board according to the expansion-board documentation.

  • Secure power bank holder with two M2 6mm hex screws

    Screw two Hex M2 6mm screws on the side of the nanosaur tracks to hold the power bank holder.

Common problems

  • Camera device cannot be opened inside Docker #34 #2
  • ROS communication fails because environment variables are not loaded #38 #40
  • Install scripts hardcode Foxy and lack version and dependency checks #6 #75 #89 #98
  • Docker fails to start after system updates #36
  • Controller and display I2C bus assignments must match hardware wiring #3

Parts

  • NVIDIA Jetson Nano devkit (2 GB or 4 GB), or a Seeed alternative carrier with a 128 GB NVMe SSD; 64 GB microSD
  • 2 Pololu 6V 150 RPM micro metal gearmotors driven by an Adafruit DC Motor + Stepper FeatherWing
  • Raspberry Pi Camera v2 (or the fisheye, ZED mini or RealSense D435i covers), 2 × 0.96-inch 128×64 I2C OLEDs
  • 5 GHz Wi‑Fi USB dongle; a PD power bank (3W minimum, bay up to 66×94×24 mm); power draw 4W for the Jetson plus 1.5W for the motors
  • nanosaur expansion board (20×80 mm, 2×20 header, terminal block, slide switch) with 1.27 mm rainbow ribbon cable; 6 F686ZZ bearings, 10 4×2 mm magnets, M2 hex screws
  • 3D prints: PLA base, front and rear, cover, sliders, sprockets and wheels, plus TPU tracks; about 10×12×6 cm and 500 g assembled

Tools

  • 3D printer (TPU for the tracks; NinjaTek recommended on Bowden printers)
  • Soldering iron for the motor driver, motor leads and expansion board
  • Screwdriver set and M2 hex key, optionally an M2 electric screwdriver
  • Optional: Noctua 4 cm fan, Logitech F710 gamepad

Skills

  • Soldering and ribbon-cable harnesses
  • Linux, NVIDIA Jetson and Docker
  • ROS 2 and Isaac ROS (site courses at beginner, intermediate and hacker level)
  • Optional: Gazebo and Isaac Sim simulation

Software

  • nanosaur 2.0.0‑pre2 (2025‑02‑20, nanosaur2 branch): ROS 2 Humble with Isaac ROS 3.2, Docker images robot, simulation and diagnostic
  • nanosaur CLI 0.1.4 (PyPI): installation, robot configuration, simulation launch and swarm control
  • nanosaur_simulation (Gazebo and Isaac Sim), nanosaur_perception (RealSense, ZED)
  • Legacy 1.x (up to 1.7.0, 2022‑09): started on ROS 2 Foxy, Jetpack 4.6 from 1.4.1, Isaac ROS integration from 1.6.0

Documents