Connecting to sources…

How to build Mujina (ムジナ) research-and-development quadruped

63 steps to build Mujina (ムジナ) research-and-development quadruped, with the source documents.

No published price: RT's press release says Mujina has been made to order since iREX 2025, with pricing through its sales team ([email protected]); RT's web store ai.rt-shop.jp does not list it (2026‑11‑03). The repo has no BOM and the creators give no build cost

Buy parts

  • Prepare the motor cable

    Prepare the motor connection cable included with the motor.

  • Prepare the XT60-to-Type-C cable

    Prepare the XT60-to-Type-C cable included with the charger.

  • Prepare the RT power hub board

    Prepare an RT power hub board.

  • Prepare the RobStride writer board

    Prepare a RobStride writing board.

  • Prepare connection jumper wires

    Prepare jumper wires for making the connections.

  • Order the Mujina research robot

    Mujina is the research and development model introduced as the first-stage, number-zero model of the domestic quadruped robot project, intended for light-load research involving patrol, inspection, and surveying.

Assemble

  • Consult the wiring diagram

    Perform the wiring while referring to the wiring diagram.

  • Attach the white USB extension cables

    Attach the USB extension cable to the two white USB cables.

  • Attach the black CtoC USB cable

    Attach the black CtoC USB cable at the position indicated by the arrow in the image.

  • Attach the HDMI extension cable

    Attach the HDMI extension cable.

  • Connect the nine-axis IMU sensor

    Connect the USB-output nine-axis IMU sensor module V3 with a white USB cable.

  • Prepare the PH3 cable connection

    Cut the PH3 pin cable to about 50 mm and attach it to the terminal block on the USBCAN interface. Confirm CANH, CANL, and GND on the board and interface while attaching it.

  • Mount the USBCAN interface

    Attach the USBCAN interface to the board with double-sided tape.

  • Connect LattePanda to USB-CANFD

    Connect LattePanda IOTA → white USB cable → USB-CANFD interface ①.

  • Connect LattePanda to the DC converter

    Connect LattePanda IOTA → black CtoC USB cable → DCDC48to24V-USB-PD ②.

  • Connect the DC fan cable

    Connect the DC fan cable to DCDC48to24V-USB-PD ③.

  • Install the XT30 female cable

    Attach the XT30 female cable. Install it exactly at the position shown in the photo, and not at either of the two red-X locations on the front board.

  • Prepare the 350 mm right motor cable

    Prepare a motor cable with a 350 mm right end.

  • Prepare the 250 mm left motor cable

    Prepare a motor cable with a 250 mm left end.

  • Prepare another 250 mm left motor cable

    Prepare another motor cable with a 250 mm left end.

  • Prepare another 350 mm right motor cable

    Prepare another motor cable with a 350 mm right end.

  • Prepare the 600 mm right motor cable

    Prepare a motor cable with a 600 mm right end.

  • Prepare the 450 mm left motor cable

    Prepare a motor cable with a 450 mm left end.

  • Prepare another 450 mm left motor cable

    Prepare another motor cable with a 450 mm left end.

  • Prepare another 600 mm right motor cable

    Prepare another motor cable with a 600 mm right end.

  • Prepare the 150 mm left motor cable

    Prepare a motor cable with a 150 mm left end.

  • Prepare another 150 mm left motor cable

    Prepare another motor cable with a 150 mm left end.

  • Prepare the 350 mm left motor cable

    Prepare a motor cable with a 350 mm left end.

  • Prepare another 350 mm left motor cable

    Prepare another motor cable with a 350 mm left end.

  • Connect the front and rear motors

    Connect the board's XT30 (2+2) connectors to the front and rear motors with their respective motor cables.

  • Route the rear motor and USB cables

    Route the rear motor cable and USB extension cable through the upper part of the battery case as shown in the image.

  • Install the insulated power button cable

    Install the power button cable at the red-arrow location, insulating the wire end before installation. The adjacent button cable at the blue-arrow location is not used in this version.

  • Attach two EC5-to-XT60 cables

    Attach two EC5-to-XT60 cables.

  • Mount the USB hub

    Mount the USB hub with double-sided tape. The USB extension cable included with the game controller may also be used depending on development status.

  • Install brass spacers

    Attach four brass spacers (BSB-310E) to four locations on FrameBodyInner.

  • Mount LattePanda IOTA

    Mount the LATTEPANDA IOTA with the pin socket facing the front of the robot.

  • Secure with M3x10 screws

    Use four hex-socket M3x10 screws to fasten and secure it at four locations.

  • Install as shown and confirm direction

    Install it as shown in the image; the left side of the image as viewed is the front of the robot.

  • Install the LattePanda

    Install the LATTEPANDA in the Mujina. Refer to lattepanda.md for the installation procedure.

  • Wire the Robot Interior

    Refer to cable.md when wiring the motor cables and other wiring inside the Mujina.

  • Insulate Unused XT30 Connectors

    For motors without a motor cable connected, insulate the XT30 (2+2) connector.

  • Install modules into the robot

    After flashing the firmware, install the USB-output 9-axis IMU sensor module V3 and the “WeAct” USB-CANFD interface into the robot body.

  • Connect the components using the photos

    Use the connection photos to connect the motor, power hub board, writing board, and jumper wires.

Software

  • Extract and run motor_tool.exe

    Extract the downloaded ZIP file, then run “motor_tool.exe” inside it.

  • Handle the first-start warning

    A Windows warning appears on first startup, followed by the home screen.

  • Change the language to English

    Change the MotorStudio language from Chinese to English.

  • Refresh and view the COM port

    After connecting the motor, writing board, and other components, click “RefreshCOM”; the connected COMPort appears in the upper box.

  • Open the serial port and read CAN ID

    Click “Open Serial Port”, then unplug and reconnect the power-connected cable once to display the CAN ID.

  • Click erase first

    In “OAT” on the left operation panel, click “erase” first.

  • Open the downloaded firmware file

    Click “open file”, select the downloaded bin firmware file, and open it.

  • Start and complete the firmware update

    Click “start update” to begin; the update is complete when the green gauge reaches 100%.

  • Flash firmware onto both modules

    Flash the USB-output 9-axis IMU sensor module V3 and the “WeAct” USB-CANFD interface with their respective firmware.

  • Download IMU firmware binary

    Download the binary to be flashed from the Releases page of the rt-usb-9axis-imu3-stm32duino-fw firmware repository.

  • Flash IMU with STM32CubeProg

    Use STM32CubeProg to flash the downloaded firmware binary onto the USB-output 9-axis IMU sensor module V3.

  • Download USB-CANFD firmware

    Download the binary to be flashed from the v0.1.0-WeActStudio_USB2CANFDV1 release page of the candleLight_fw firmware repository.

  • Erase USB-CANFD flash first

    Before flashing the firmware, completely empty the Flash by following “How to completely empty Flash” in the WeActStudio GitHub README.

  • Set Motor IDs and Update Firmware

    Set each motor’s ID according to the assignment shown in the image. Refer to motor_tool.md for ID writing and firmware updating.

  • Flash Sensor and Interface Firmware

    The USB output 9-axis IMU sensor module V3 and the WeAct USB-CANFD interface both require firmware. Follow firmware.md for writing, then install them in the robot.

  • Prepare the LattePanda PC

    Before assembly, set up the PC by following the Mujina_ros README.

Calibrate and test

  • Refresh and view the parameter table

    Click “RefreshPara Table” to display the parameter list.

  • Enter the CAN ID to write

    Click the number beside “Set ID” in the left “Motor Configration” panel and enter the number to write.

  • Click Set ID

    Click “Set ID” to write the entered ID.

  • Refresh the table and confirm the ID

    Click “RefreshPara Table”; the table refreshes and the ID change can be confirmed.

Parts

  • 12 joint motors, one each for the collar (abduction), hip and knee of every leg, IDs 1–6 front and 7–12 rear; the assembly docs set them up as RobStride RS02
  • A LattePanda IOTA computer inside the body (set to power on automatically)
  • RT's USB 9-axis IMU module V3; WeAct USB‑CANFD adapters (flashed with RT's candleLight firmware)
  • RT's power hub board, a DCDC 48V-to-24V USB‑PD board, XT30 (2+2) motor cables, EC5-to-XT60 battery cables, a USB hub, a fan and a power button

Tools

  • ST‑Link V2/V3 and STM32CubeProgrammer (to flash the IMU and USB‑CANFD firmware)
  • RobStride Motor Studio (Windows) and the RobStride programming board, to set motor CAN IDs and update the RS02 firmware
  • A Logicool F710/F310 gamepad
  • Gloves and safety shoes (a measure in the designer's risk assessment)

Skills

  • Ubuntu 24.04, ROS 2 Jazzy and two-bus CAN setup
  • Reinforcement-learning training with Isaac Sim 5.1 / Isaac Lab 2.3 and MuJoCo simulation
  • Motor zero calibration and internal wiring (unused XT30 connectors must be insulated)

Software

  • mujina_ros: ROS 2 Jazzy control, MuJoCo simulation and URDF, with a trained policy.onnx (v0.1.0, 2026‑07‑14, for the Mujina Alpha Model only)
  • mujina_isaac_lab: an Isaac Lab training project (forked from mevius_isaac_lab)
  • rt-usb-9axis-imu3-stm32duino-fw (IMU) and candleLight_fw (USB‑CANFD) firmware

Documents