Connecting to sources…

How to build MickRobot: the whole process

31 steps to build MickRobot, from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop links and the official sour…

MickRobot is a single-arm mobile robot that integrates a 7-DOF arm with a mobile chassis for grasping and handling tasks in complex environments. The repository provides the chassis 3D mechanical drawings, STM32 controller and power-board designs, embedded and ROS code, and operating and assembly documentation.

Bill of materials · table 1

PartQty
1 · Hub Motor · WS80L-07A250C4
2 · Motor Driver · L2DB48302
3 · Battery · LiFePO4 Battery 29.4V20AH1
4 · Control Board (VCU) · Custom STM32F407-IN8731
5 · Power Supply Board · Custom 19V-3A /12V-2A /5V-2A1
6 · Remote Controller · RC Transmitter T8FB Control + R8FM1
7 · USB-to-RS232 Serial Cable · UGREEN1
8 · 7.2V Lithium Battery Charger · Purchased with the remote controller1
9 · 29.4V Lithium Battery Charger · Purchased with the battery1

Bill of materials · table 2

PartQty
1 · Battery Level Display Unit · 7S Fully Charged 29.4V Li-ion Battery1
2 · Charging Extension Cable 5521 · Cable Length 50CM, 5.5X2.1 Socket, 5.5X2.1 Metal Plug, 18AWG (10A)1
3 · Aviation Connector 2p Gx16 · Power and External Cables, Cut Length 90cm, with a Fuse in Series About 10cm from the End1
4 · Emergency Stop Switch · 16mm Metal Emergency Stop, 2NO 2NC1
5 · Power Switch · 16mm Latching Pushbutton, Ring + Power Symbol1
6 · Industrial Indicator Light Harness / Three-Color LED1
7 · D-Sub RS232 Panel Connector1
8 · RS232 Extension Cable1
9 · D-Sub Type-C Debug Port1

Buy parts

  • Prepare power and control components

    Prepare four 8-inch hub motors, two one-to-two drivers, a 7S lithium battery with a BMS protection board, a relay, a main control board, and an SBUS receiver.

  • Obtain the mechanical model files

    Obtain the STEP files for fabrication from Baidu Netdisk at https://pan.baidu.com/s/1Tm8cC3vw8Vl4whnVbb_SAA?pwd=bcp2, using the extraction code bcp2.

  • Obtain the enclosure model files

Print and make

  • Fabricate the two-plate chassis

    Use mickrobotV3-20240628.STEP to fabricate the upper and lower aluminum plates, motor mounting brackets, and light-shaft columns. This simple scheme can be used for straightforward chassis replication.

  • Fabricate the optional welded frame

Assemble

  • Use the V3 control board

    The third-version chassis control board uses an STM32F407 as its main controller.

  • Wire the V1 control board power

    The first-version board uses an STM32F103 and accepts 20-36V DC input. It provides DC 5V 2A and DC 12V 2A outputs for onboard sensors.

  • Connect control board interfaces

    Connect the DBUS interface to the telemetry remote controller, the 232 interface to the ROS host computer, the CAN bus to four M3508 motors, and the IIC interface to the onboard MPU9250. The 485 and UART3 interfaces are multiplexed and can connect other sensor modules.

  • Connect controls and isolated I/O

    Connect three status LEDs, two pushbuttons, and four DIP switches. Connect four isolated inputs rated for 12-24V and four isolated outputs that switch between high-impedance and GND and tolerate 2A.

  • Check control board dimensions

    The first- and third-version boards have the same outline and mounting-hole positions. The board is 99×99 mm, with 93 mm hole-center spacing and φ3.1 mm holes.

  • Connect the power board input

    Connect a 20-36V DC power source to the chassis power board input.

  • Connect the 5V output

    Connect the power board’s single DC 5V 2A output.

  • Connect the adjustable output

    Connect the power board’s single adjustable DC 3.3-19V 2A output.

  • Connect the 12V output

    Connect the power board’s single DC 12V 3.5A output.

  • Connect the 19V output

    Connect the power board’s single DC 19V 3.5A output.

  • Connect battery, relay, and drivers

    Connect the 29.4V/20AH power battery through the relay to the power system, then place one one-to-two motor driver on each side. Connect each driver to the two hub motors on the same side.

  • Connect CAN and the radio receiver

    Connect the motor drivers to the main control board through the CAN bus, and connect the SBUS radio receiver to the main control board.

  • Connect the external interface panel

    Integrate the emergency stop, power switch, battery-level display, charge and discharge ports, indicator light, 232 serial port, and Ethernet port on the external panel for interaction and debugging.

  • Assemble the two-plate chassis

    Mount the motors to the lower plate using the motor brackets, and support the upper and lower plates with light-shaft columns.

Software

  • Set Two-Wheel Motor IDs

    Set the chassis motor IDs to 1 and 3 to use the same commands as the four-wheel differential chassis.

Calibrate and test

  • Check Chassis Status Lights

    A flashing green light is normal. Flashing green with a steady red light means the emergency stop is not released; a rapidly flashing yellow light at startup means no remote-control signal; and four slow red flashes at startup mean the IMU is not initialized.

  • Configure Ethernet Debugging Connection
  • Configure Network Serial Debug Tool

    Set the default port to 8234, the serial baud rate to 921600, and the working mode to TCP server to print chassis debugging information.

  • Reset Serial-to-Ethernet Module

    Open the chassis enclosure and short the module GND to RST pin 4 for at least 200 ms. After reset, the module default IP address is 192.168.0.7 and its communication baud rate is 115200.

Use it

  • Identify Chassis Panel Ports

    The first row contains the battery display module, emergency-stop button, three-color indicator, and power button. The second row contains the battery charging port, 24V/10A external power port, RS232 port, and Ethernet debugging port; the external power connector uses GX16-2, with pin 1 as +VCC and pin 2 as GND.

  • Charge the Chassis Battery

    Use the matching charger and insert its round plug into the panel charging port. The charger is about 180 W, outputs 24-29.4 V, and takes approximately 4-5 hours.

  • Select Remote Control Mode

    Set the upper-left remote switch to L to enable autonomous driving, making remote input ineffective. Set it to H to control the chassis by radio and ignore host-computer commands.

  • Select Chassis Travel Speed

    The upper, middle, and lower positions of the upper-right remote switch set chassis speeds to 1 m/s, 2 m/s, and 2.2 m/s.

  • Drive and Turn the Chassis

    Use the left stick's vertical channel ch3 to move the chassis forward and backward, and the right stick's horizontal channel to turn it left and right.

  • Replace Low-Voltage Remote Battery

    When the remote battery voltage is low, it emits a beeping sound. Open the rear cover, remove the battery, and match the connector polarity to the “+” and “-” marks on the back of the remote.

  • Charge the Remote Battery

    Charge with the matching remote charger; the charger light changes from red to green when full. The remote uses a 2S battery with a voltage range of 6.4-8.4 V.

Documents