Connecting to sources…

How to build SO-ARM 102: the whole process

58 steps to build SO-ARM 102, from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop links and the official sou…

SO-ARM 102 is an open-source leader–follower robot arm kit for teleoperation and imitation learning, with five degrees of freedom plus a gripper per arm. The repository provides printable 3MF, STL, and STEP files, a bill of materials, printing and assembly guides, and setup instructions.

Bill of materials · Electronics

PartQtyUSEU
Waveshare Bus Servo Adapter2USD 7.4EUR 11.9
Power supply 12V DC (12V 5A power supply 5.5 2.1mm)1USD 6.6EUR 12
Power supply 5V DC (5V 2A power supply 5.5 2.1mm)1USD 4.1EUR 11
USB-C cable, 1.5 m (USB A to USB C data cable 1.5m)2USD 3EUR 7
USB camera (OV2735, 1080P USB Camera Module, 2MP 1920x1080, UVC Camera, 2.8 or 3.0 mm lens)1USD 26.1EUR 21

Bill of materials · Mechanical parts

PartQtyUSEU
Ball bearing 6812 · 60 × 78 × 10 mm · Base rotation, one per arm2USD 39.6EUR 7.4
Flanged bearing MF106ZZ · 6 × 10 × 3 mm · Gripper main frame2USD 6EUR 11.6
Rod (Stainless Steel Round Rod, 6mm Diameter, Length 125mm) · Ø6 × 125 mm, carbon or steel · Gripper guides2USD 2.8EUR 14.4
Aluminium guide tube, alternative · Ø6 × 4 × 125 mm; cut 1 × 300 mm into 2 × 125 mm; deburr · Alternative to steel gripper guide rods2USD 4.1EUR 14.9
Carbon tube (Carbon tube, 6mm x 4mm x 125mm), alternative · Ø6 × 4 × 125 mm · Alternative to steel gripper guide rods2USD 5.9EUR 8.1
C-clamp · 3 inch, 0–75 mm opening · Two per arm, to fix the base to the table4USD 9.7EUR 17.4
Rubber O-ring · 8 × 2 mm · Adds friction to the leader joints. Two per servo on joints 2–4, one on joints 1, 5, 6.10USD 2.3

Buy parts

  • Buy components for two arms

    Order the components for one follower arm and one leader arm. The estimated component cost is $342.4, or $388.4 including printing material.

  • Confirm parts before ordering

    Confirm the selected variants, minimum order quantities, and prices before ordering. Shipping, taxes, tools, a computer, a printer, electricity, and assembly labour are excluded from the estimate.

  • Select the listed servo types

    Use 6 × STS3215 7.4V, 2 × STS3215 12V, 2 × STS3235 12V, and 2 × STS3250 12V Feetech TTL serial bus servos. The STS3250 drives the follower's two highest-load joints, while the leader servos are only read and never loaded.

  • Choose the passive leader servo

    For the 5V leader arm, use a passive ST-3215-C066 without a motor or gearbox. A passive servo is only suitable for the leader arm.

  • Buy two additional long cables

    The follower and leader require 4 long cables and 8 standard cables. Buy two additional 22 cm-or-longer cables; the STS3250 cables are 22 cm and the STS3215 cables are 17 cm.

  • Buy the listed electronics

    Purchase the six electronics listed in the Electronics table.

  • Buy the listed mechanical parts

    Purchase the eight mechanical parts listed in the Mechanical parts table.

  • Buy the packed fastener kit

    Use the quantities in the Fasteners table and the totals as packed in the assembly booklet. Obtain a removable threadlocker compatible with the printed plastic, such as Vibra-Tite VC-3.

  • Choose the printing material

    The prototype used Fiberon PET-CF17. See Choosing a filament for robotic arms for details on filament selection.

  • Buy one complete set

    Obtain the parts listed under Common parts, Follower only, and Leader only. The quantities cover one complete kit with one follower and one leader.

  • Check the 6.1 mm rod bore

    D6.1 means the rod bores are sized for 6.1 mm. If the gripper runs tight, see the known issues in the main README.

  • Collect the Listed Hardware

    Collect the hardware listed in bom.md before starting.

  • Prepare the Required Hex Keys

    Prepare a 1.5 mm hex key for M2 screws and a 2 mm hex key for M3 screws.

  • Buy a ready SO-ARM 102 kit

    Prefer a ready kit? Buy the SO-ARM 102 kit.

Print and make

  • Download all printed-part files

    Get every printed part of the kit from `../models/stl/` and the editable CAD sources with the same names from `../models/step/`.

  • Do not anneal impact parts

    Annealing makes the part more brittle, so do not anneal parts that take impacts.

  • Slice in Bambu Studio

    Open the supplied 3MF projects in Bambu Studio, select your printer and filament, then slice and review the support preview.

  • Split layouts for smaller beds

    Individual parts still fit a 180 × 180 mm bed, but the supplied layouts must be split across more plates at that size.

  • Review support settings

    Automatic tree supports are the global default; some parts have support overrides, manual support settings, or support blockers.

  • Set gripper gearing infill

    Use 100% infill for the gripper gear and gear racks.

  • Increase follower arm stiffness

    With 100% infill on all links and 35% on the base, gripper deflection under 300 g dropped from 3.4 mm to 2.34 mm.

  • Keep leader infill low

    Keep the leader's infill low because it only has to be light and quick to print.

  • Orient parts correctly

    Upper arms print best tilted, producing a clean surface without cracking the thin section. Lay long parts so the layer lines run along their length.

  • Print parts common to both arms

    Print the STL parts in the common-parts table for both the follower and leader, using the listed quantities for one complete kit.

  • Print follower-only parts

    Print the STL parts in the follower-only table, using the listed quantities for one complete kit.

  • Print leader-only parts

    Print the STL parts in the leader-only table, using the listed quantities for one complete kit.

  • Export STL from STEP

    The STL files were exported from the STEP sources with a chord tolerance of 0.02 mm. If you change a part, edit the STEP and export a new STL with the same name.

  • Open Projects in Bambu Studio

    Open the three 3MF projects in Bambu Studio to retain the saved settings.

  • Select Printer and Filament Settings

    All three use the Bambu Lab A1, 0.4 mm nozzle profile and one 256 × 256 mm plate each. Select the printer, nozzle, and filament before slicing; for a smaller bed, split the parts across additional plates while preserving their orientations and support settings.

  • Print All Three Projects

    For one leader and one follower, print all three projects once.

  • Print the Gripper Rod Test Plate

    Print the Gripper rods test plate with the same material and settings as the Clamps (PETG-CF) so the Follower Gripper moves smoothly.

  • Print Matching Follower Table

    After the test, print one of the three Follower table 2 3MF versions, with D6.0, D6.1, or D6.2 at the end of the filename, matching the tested hole size.

  • Print the Assembly Booklet

    Print the booklet on A5 landscape if you prefer paper.

  • Print All Robot Parts

    Print all parts listed in printing.md before starting the assembly.

  • Obtain the printed parts

    Use the separately listed printed parts for the follower and leader arms. Printing quantities are budget allowances, so re-slice the supplied 3MF projects for your settings.

  • Print the robot parts

    Print the leader, follower arm links, and follower gripper and base. Individual parts fit a 180 × 180 mm bed; the supplied 3MF plate layouts use a 256 × 256 mm bed, and the largest part is 160 mm long.

Assemble

  • Read Ahead Before Tightening

    Read two steps ahead before tightening anything. Two places in the current order are awkward and are identified in the known issues.

  • Keep the Power Supplies Separate

    The leader runs on 5 V and the follower runs on 12 V. Keep their power supplies apart.

  • Apply Threadlocker to Metal Threads

    Apply Vibra-Tite VC-3 to metal screw threads and let it dry fully before assembly. Allow at least 30 minutes.

  • Keep Threadlocker Wet Plastic Away

    Do not apply the threadlocker wet to plastic. Confirm compatibility with the filament on a spare print first.

  • Read the assembly illustrations

    Use the beige highlights to identify new parts and the grey parts to identify components already assembled. Match each part thumbnail and quantity to the numbered assembly step.

  • Mount the servo horns

    Mount one horn on servo ID 1 with an M3 × 6 servo-kit screw, and mount a horn on both sides of servo IDs 2, 3, and 4. If adding O-rings to the leader, place them between each servo and its horn.

  • Build both arm bodies

    Build the arm body twice, once for the follower and once for the leader, following arm steps 1–13. Use the printed part names that match printing.md.

  • Check servo cable slack

    Before closing each joint, verify that its servo cable reaches the next joint with some slack.

  • Build the parallel gripper

    Build the parallel gripper by following gripper steps 1–6.

  • Finish the follower arm

    Finish the follower arm by adding the camera holder, gripper, and camera in follower steps 1–3.

  • Finish the leader arm

    Finish the leader arm by adding the handle and trigger in leader steps 1–2.

  • Clamp Both Bases

    Clamp each base to the table with two C-clamps.

  • Connect Controllers to Power

    Connect the follower controller to the 12 V supply and the leader controller to the 5 V supply.

  • Connect Controllers to Computer

    Connect both controllers to the computer with USB-C.

  • Connect servo IDs with long cables

    Use the additional long cables to join servo ID1 to ID2 and servo ID3 to ID4. Follow the linked assembly guide for the connections.

  • Test threadlocker on a spare print

    Confirm that the removable threadlocker is compatible with your filament by testing it on a spare print first. Do not apply it wet to plastic.

  • Apply and dry VC-3 threadlocker

    Apply VC-3 only to metal screw threads and let it dry fully before assembly. Allow at least 30 minutes for drying; do not apply VC-3 wet to plastic.

Calibrate and test

  • Set all servo IDs

    Set each servo ID before installing it in the arm. ID-setting and calibration tools are available at lab.robonine.com.

  • Calibrate and Start Teleoperation

    Calibrate both arms and start teleoperation at lab.robonine.com, or with the LeRobot SO-101 workflow.

  • Test Rod Fit and Select Hole

    Insert the 6 mm rod into the 6.0–6.2 mm holes from largest to smallest. Choose the hole with a smooth fit and minimal play for the next step.

Use it

  • Use the single-arm configuration

    Move the leader by hand, and the follower repeats the motion. Use this configuration for teleoperation and for recording demonstrations for imitation learning.

  • Use the bimanual configuration

    Place two kits side by side. Each hand drives its own leader, allowing the followers to pass objects, hold and work on a part, or perform a task that needs two hands.

Documents