Connecting to sources…

How to build SO-ARM 102: the whole process

104 steps to build SO-ARM 102, from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop links and the official so…

SO-ARM 102 is an open-source leader + follower robot arm kit with a 5-DOF follower, parallel gripper, and a hand-driven leader for teleoperation and imitation learning. The repository provides 3MF/STL print files, STEP CAD sources, a bill of materials, printing and assembly guides, and LeRobot setup information.

Bill of materials · Electronics

PartQtyUSEU
Waveshare Bus Servo Adapter2USD 7.4EUR 11.9
Power supply 12V DC (12V 5A power supply 5.5 2.1mm)1USD 6.6EUR 12
Power supply 5V DC (5V 2A power supply 5.5 2.1mm)1USD 4.1EUR 11
USB-C cable, 1.5 m (USB A to USB C data cable 1.5m)2USD 3EUR 7
USB camera (OV2735, 1080P USB Camera Module, 2MP 1920x1080, UVC Camera, 2.8 or 3.0 mm lens)1USD 26.1EUR 21

Bill of materials · Mechanical parts

PartQtyUSEU
Ball bearing 6812 · 60 × 78 × 10 mm · Base rotation, one per arm2USD 39.6EUR 7.4
Flanged bearing MF106ZZ · 6 × 10 × 3 mm · Gripper main frame2USD 6EUR 11.6
Rod (Stainless Steel Round Rod, 6mm Diameter, Length 125mm) · Ø6 × 125 mm, carbon or steel · Gripper guides2USD 2.8EUR 14.4
Aluminium guide tube, alternative · Ø6 × 4 × 125 mm; cut 1 × 300 mm into 2 × 125 mm; deburr · Alternative to steel gripper guide rods2USD 4.1EUR 14.9
Carbon tube (Carbon tube, 6mm x 4mm x 125mm), alternative · Ø6 × 4 × 125 mm · Alternative to steel gripper guide rods2USD 5.9EUR 8.1
C-clamp · 3 inch, 0–75 mm opening · Two per arm, to fix the base to the table4USD 9.7EUR 17.4
Rubber O-ring · 8 × 2 mm · Adds friction to the leader joints. Two per servo on joints 2–4, one on joints 1, 5, 6.10USD 2.3

Buy parts

  • Confirm and order the component list

    Use the quantities for one complete kit containing one follower arm and one leader arm. The estimated component cost is $342.4, or $388.4 including printing material, before shipping, taxes, tools, a computer, a printer, electricity, and assembly labour.

  • Buy the listed Feetech servos

    Use six STS3215 7.4V, two STS3215 12V, two STS3235 12V, and two STS3250 12V servos. All are Feetech TTL serial bus servos.

  • Assign servos to the follower arm

    Use the 12V STS3250 for the follower arm; it is a 50 kg·cm brushless servo running at 75 RPM for the two most heavily loaded joints. The STS3235 is a 30 kg·cm servo with lower backlash than the STS3215.

  • Choose the leader-arm servos

    Use 5V servos for the leader arm, where the servos are only read and never loaded. A passive ST-3215-C066 without a motor and gearbox may be used only for the leader arm.

  • Check the included horns and screws

    Check that the servo horns and M3 × 6 horn screws are included with the servos.

  • Compare the supplied servo cable lengths

    The STS3250 servos include 22 cm cables. The STS3215 servos include 17 cm cables.

  • Buy two additional long cables

    The follower and leader require four long cables and eight standard cables. Purchase two additional cables that are 22 cm or longer, and use them to join servo ID1 to ID2 and ID3 to ID4.

  • Select compatible removable threadlocker

    Select a removable threadlocker compatible with the printed plastic, such as Vibra-Tite VC-3.

  • Obtain the required tools

    Allow about $10.0 for a small hex-key and screwdriver set if you do not already own these tools.

  • Collect the required hardware

    Collect the hardware listed in bom.md.

  • Prepare the hex keys

    Prepare a 1.5 mm hex key for M2 hardware and a 2 mm hex key for M3 hardware.

  • Buy the SO-ARM 102 Kit

    Buy the complete SO-ARM 102 kit instead of sourcing the components and printing the parts yourself.

  • Buy a ready SO-ARM 102 kit

    Choose the ready-made SO-ARM 102 robotic arm kit instead of sourcing and making the parts individually.

Print and make

  • Download STL and CAD files

    Download all printed-part STLs from `../models/stl/` and the editable CAD sources with the same names from `../models/step/`.

  • Print shared and controller-case parts

    Print the shared parts in `common/`, including the controller cases.

  • Print follower parts

    Print the parallel gripper and camera mount in `follower/`.

  • Print leader parts

    Print the handle, trigger, and wrist roll in `leader/`.

  • Check the printer-bed size

    Confirm that every part fits a 180 × 180 mm bed; the largest part, the base, measures 160 × 112.5 mm.

  • Choose the printing material

    The prototype was printed in Fiberon PET-CF17. Testing showed that annealing reduces PET-CF17 deflection but makes parts more brittle, so do not anneal parts that take impacts.

  • Slice in Bambu Studio

    Open the 3MF files as projects in Bambu Studio, select your printer and filament, then slice and review the support preview.

  • Check the saved printer profile

    All three projects save a Bambu Lab A1, 0.4 mm nozzle, and 256 × 256 mm bed profile. For a 180 × 180 mm bed, split the supplied layouts across more plates.

  • Review part support settings

    Automatic tree supports are the global default, while some parts have support overrides, manual support settings, or support blockers.

  • Set gripper-gear infill

    Use 100% infill for the gripper gear and gear racks.

  • Increase follower rigidity

    Use 100% infill on all links and 35% on the base to increase follower rigidity.

  • Estimate follower material and time

    This infill setting takes about 720 g of filament and 27 h instead of 500 g and 21 h; the gripper is not included.

  • Keep leader infill low

    Keep the leader infill low because it only needs to be light and quick to print.

  • Set part orientations

    Upper arms print best tilted, producing a clean surface and avoiding cracks in thin sections; lay long parts so the layer lines run along their length.

  • Open projects in Bambu Studio

    Open all three 3MF files as projects in Bambu Studio to retain the saved settings.

  • Select settings and slice

    All three use the Bambu Lab A1, 0.4 mm nozzle profile and one 256 × 256 mm plate each. Select the printer, nozzle and filament before slicing.

  • Split parts for a smaller bed

    For a smaller bed, split the parts across additional plates while preserving their orientations and support settings.

  • Print one leader and follower

    For one leader and one follower, print all three projects once.

  • Print the gripper rod test plate

    First print the gripper rods test plate using the same material and settings as the Clamps: PETG-CF.

  • Print the matching Follower version

    After the test, print one of the three Follower table 2 3MF versions whose filename ends with D6.0, D6.1 or D6.2, matching the tested hole.

  • Download the prepared 3MF projects

    Download the supplied 3MF slicer projects for the leader, follower arm links, and follower gripper and base. The projects include saved orientation and support settings.

  • Check printer profiles and project contents

    Open `models/README.md` to check the project contents and printer profiles.

  • Choose STL or STEP model files

    Use the STL files, which are ready to slice, or download the STEP sources. The STL files are in `models/stl/`, and the STEP sources are in `models/step/`.

  • Check material and print settings

    Open `docs/printing.md` for the required material, printer settings, and quantities of each part.

  • Confirm the printer bed size

    Use a 256 × 256 mm bed for the supplied 3MF plate layouts. Individual parts can fit on a 180 × 180 mm bed, and the largest individual part is 160 mm long.

  • Print the assembly booklet

    Print the SO-ARM102 assembly booklet on A5 landscape if you prefer paper.

  • Print all robot parts

    Print all parts according to printing.md.

  • Prepare the printed parts

    Find the printed-part instructions separately in printing.md. Re-slice the supplied 3MF projects for your settings; the full-pack allowances are a 0.5 kg spool of PET-CF17 and 1.0 kg spools each of PETG-CF and PLA+.

  • Estimate printing filament

    Use the printing guide and re-slice the supplied 3MF projects to determine the filament quantity for your printer and settings.

Assemble

  • Read ahead before tightening

    Read two steps ahead before tightening anything. Check the Known issues section for two awkward places in the current order.

  • Keep the power supplies separate

    The leader runs on 5 V and the follower runs on 12 V. Keep their power supplies apart.

  • Prepare compatible threadlocker

    Use a removable threadlocker compatible with the printed plastic, such as Vibra-Tite VC-3. Apply it to metal screw threads, let it dry fully for at least 30 minutes before assembly, do not apply it wet to plastic, and confirm compatibility with your filament on a spare print first.

  • Mount Horn on Servo ID 1

    Mount one horn on servo ID 1 using an M3 × 6 servo-kit screw. The screw marked “servo kit” comes from the servo pack.

  • Mount Both-Side Horns

    Mount a horn on both sides of servos ID 2, 3 and 4. Use the horn screws supplied with the servos.

  • Fit Leader Servo O-Rings

    If adding O-rings to the leader, place each ring between the servo and its horn. The wrong order can jam the ring between the servo shell and the horn.

  • Build Arm Body Step 1

    Build arm-body step 1 once for the follower and once for the leader. Printed part names match printing.md.

  • Build Arm Body Step 2

    Build arm-body step 2 for both the follower and the leader.

  • Build Arm Body Step 3

    Build arm-body step 3 for both the follower and the leader.

  • Build Arm Body Step 4

    Build arm-body step 4 for both the follower and the leader.

  • Build Arm Body Step 5

    Build arm-body step 5 for both the follower and the leader.

  • Build Arm Body Step 6

    Build arm-body step 6 for both the follower and the leader.

  • Build Arm Body Step 7

    Build arm-body step 7 for both the follower and the leader.

  • Build Arm Body Step 8

    Build arm-body step 8 for both the follower and the leader.

  • Build Arm Body Step 9

    Build arm-body step 9 for both the follower and the leader.

  • Build Arm Body Step 10

    Build arm-body step 10 for both the follower and the leader.

  • Build Arm Body Step 11

    Build arm-body step 11 for both the follower and the leader.

  • Build Arm Body Step 12

    Build arm-body step 12 for both arms and fit a Bus Servo Adapter on each arm.

  • Build Arm Body Step 13

    Build arm-body step 13 for both arms and fit a Bus Servo Adapter on each arm. Before closing the joint, check that each servo cable reaches the next joint with some slack.

  • Build Gripper Step 1

    Build the parallel gripper by following gripper step 1.

  • Build Gripper Step 2

    Build the parallel gripper by following gripper step 2.

  • Build Gripper Step 3

    Build the parallel gripper by following gripper step 3.

  • Build Gripper Step 4

    Build the parallel gripper by following gripper step 4.

  • Build Gripper Step 5

    Build the parallel gripper by following gripper step 5.

  • Build Gripper Step 6

    Build the parallel gripper by following gripper step 6.

  • Install Follower Camera Holder

    Complete follower step 1 by installing the camera holder on the follower.

  • Install Follower Gripper

    Complete follower step 2 by installing the gripper on the follower.

  • Install Follower Camera

    Complete follower step 3 by installing the camera on the follower.

  • Install Leader Handle

    Complete leader step 1 by installing the handle on the leader.

  • Install Leader Trigger

    Complete leader step 2 by installing the trigger on the leader.

  • Assemble gripper step 1

    Follow the Gripper 1 image for the follower gripper assembly.

  • Assemble gripper step 2

    The ×2 on step 2 is one jaw assembly for each side.

  • Assemble gripper step 3

    Follow the Gripper 3 image for the follower gripper assembly.

  • Assemble gripper step 4

    Follow the Gripper 4 image for the follower gripper assembly.

  • Assemble gripper step 5

    Follow the Gripper 5 image for the follower gripper assembly.

  • Prepare gripper servo and clamps

    Before step 6, move servo ID 6 to its minimum position. Slide both clamps along the rods by hand before closing up; they should move freely without binding.

  • Assemble follower step 1

    Follow the Follower 1 image for the follower assembly.

  • Assemble follower step 2

    Follow the Follower 2 image for the follower assembly.

  • Assemble follower step 3

    Follow the Follower 3 image for the follower assembly.

  • Assemble leader step 1

    Follow the Leader 1 image for the leader assembly.

Software

  • Connect both controllers by USB-C

    Connect both controllers to the computer with USB-C.

Calibrate and test

  • Configure Leader Servo IDs

    Set each leader servo ID before installation; all leader servos are STS3215. Use the ID-setting and calibration tools at lab.robonine.com.

  • Configure Follower IDs 1 and 4

    Set the follower servo IDs before installation. Follower servo ID 1 and ID 4 are STS3235.

  • Configure Follower IDs 2 and 3

    Set the follower servo IDs before installation. Follower servo ID 2 and ID 3 are STS3250.

  • Calibrate and start teleoperation

    Calibrate both arms and start teleoperation at lab.robonine.com, or with the LeRobot SO-101 workflow.

  • Test threadlocker compatibility on a spare print

    Confirm that the threadlocker is compatible with your filament by testing it on a spare print first.

  • Test and choose the rod hole

    Try inserting a 6 mm rod into the 6.0–6.2 mm holes from largest to smallest, then choose the hole with a smooth fit and minimal play for the next step.

Use it

  • Operate a single-arm setup

    Set up one leader and one follower, then move the leader by hand so the follower repeats the motion. Use this configuration for teleoperation and recording demonstrations for imitation learning.

  • Set up a bimanual configuration

    Place two kits side by side, with each hand driving its own leader. The two followers can pass objects, hold and work on a part, or perform tasks needing two hands.

Documents