Connecting to sources…

How to build AIRA: the whole process

54 steps to build AIRA, from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop links and the official sources.

AIRA is a 3D-printable 7-DoF robotic arm consisting of a 6-DoF arm and a 1-DoF gripper. The repository provides STEP CAD files, a bill of materials, assembly instructions, and LeRobot integration for teleoperation, data recording, and AI policy training.

Bill of materials · Hardware

PartQty
Damiao J8009P · 9:1 · 20 Nm / 35 Nm · 20A / 50A · Base + Link1 (follower)2
Damiao J4340P · 40:1 · 9 Nm / 27 Nm · 2.5A / 8A · Link2 + Link3 (follower)2
Damiao J4310P · 10:1 · 3 Nm / 12.5 Nm · 2.5A / 7.5A · Link4 + Link5 + Gripper (follower)3
Dynamixel XL330-M077 · Serial, 0.13 Nm · All joints (leader)7
USB-CAN adapter · e.g. Canable, MKS CANable · CAN bus interface1
RealSense D405 · Depth camera · Wrist camera (optional)1

Bill of materials · 3D Printed Parts — PLA-CF (Black)

PartQty
Base Leader · Base1
shaft_leader · Base1
bearing plate · Base2
link1_Leader · Link 11
Link2_Leader · Link 22
Link2 end Leader · Link 21
link3Part1 · Link 31
link3Part2 · Link 31
link4 · Link 41
Link5 Leader · Link 51
Gripper Insert Leader · Gripper1
Link7 (Gripper Leader) · Gripper1
Finger_holder (Gripper Leader) · Gripper1
D405 Holder · Gripper1
Finger Adapter (FingerAdapter v0.2) · Gripper / Finger2
Finger Adapter (inside Soft Finger) · Gripper / Finger2

Buy parts

  • Buy Seven Damiao Motors

    Buy seven Damiao CAN-bus motors for the Follower Arm, with a listed cost of about $1,515.

  • Buy 147 Follower Arm Screws

    Buy the 147 socket head cap screws for the Follower Arm; use black-oxide alloy steel unless noted.

  • Buy Seven Dynamixel Servos

    Buy seven Dynamixel servos for the Leader Arm, with a listed cost of about $168.

  • Buy 60 Leader Arm Screws

    Buy the 60 socket head cap screws for the Leader Arm; use black-oxide alloy steel unless noted.

  • Buy Leader Arm External Components

    Buy the two external-component entries listed for the Leader Arm.

  • Optionally Buy a Camera

    If desired, buy the optional camera listed in the bill of materials.

  • Buy an AIRA Kit or Premium Arm

    Go to the Nextis Hardware page to obtain an AIRA kit or a Premium Arm assembled robot.

  • Buy the verified kit

    Order the verified complete kit from Nextis, or choose the CNC aluminum upgrade.

  • Review hardware list and cost

    Review the hardware BOM for the complete parts list. The estimated cost for the full teleop kit, including shipping and import duties, is €2,000–€2,500 / $2,220–$2,750.

  • Buy the Verified Kit

    The Verified Kit includes the 3D-printed frame, motors, and electronics, and only needs assembly.

  • Buy the Aluminium Premium Arm

    The Aluminium Premium Arm is a CNC aluminum build that is professionally assembled and calibrated, with direct support from Nextis.

  • Choose and Reserve an AIRA

    Choose between the pre-assembled AIRA Pro and the self-assembled AIRA Core, then reserve through the page.

  • Reserve the AIRA Pro

    Reserve the AIRA Pro for €4,900 including 19% VAT. It is built to order, ships within three weeks, and arrives pre-assembled and factory-calibrated.

  • Reserve the AIRA Core Kit

    Reserve the AIRA Core for €2,999 including 19% VAT. It ships as a verified unassembled kit with an assembly guide and the hardware required for self-calibration.

  • Reserve an AIRA Kit

    Leave your details, and NEXTIS will contact you before the public release. The first batch is limited.

  • Gather all parts and tools

    Gather all 3D-printed parts and all components listed in BOM.md. Prepare a soldering iron, M3, M4, and M5 hex drivers, wire strippers, a computer with a connected USB-CAN adapter, a 24V power supply for follower motors, and a 5V power supply for leader servos.

Print and make

  • Open the interactive 3D models

    Open the Autodesk Fusion 360 interactive 3D viewers for the AIRA follower arm and leader arm through the image links.

  • Download the STEP mechanical models

    Download the STEP files for the follower arm and leader arm from the repository's `/hardware` directory.

  • Print the robot frame

    Print the frame at home with a 3D printer, or use CNC aluminum parts instead.

  • Print the parts

    Print the parts using the print settings in the assembly guide, and consult the full parts list.

  • Print 19 Black PLA-CF Parts

    Print the 19 black PLA-CF parts exported from the Follower Arm assembly.

  • Print Orange TPU Parts

    Print the orange TPU parts listed for the Follower Arm.

  • Print 15 Black PLA-CF Parts

    Print the 15 black PLA-CF parts exported from the Leader Arm assembly.

  • Print all PLA-CF structural parts

    Print all 19 structural parts in black PLA-CF with a 0.2 mm layer height and 30–40% infill. Enable supports; tree supports are recommended, and a hardened-steel nozzle is required for carbon fiber filament.

  • Print two orange TPU fingertips

    Print two `soft_finger_v1` parts in orange TPU with a 0.2 mm layer height and 20% infill. Reduce the print speed to 20–30 mm/s.

Assemble

  • Wire the CAN Bus

    Connect the CAN bus using a daisy-chain topology and place a 120 Ohm termination resistor at each end of the bus. The document marks the wiring diagram as TODO.

  • Assemble the Follower Arm

    Assemble the follower arm only after all motors have been configured and tested. The document names Base, Link 1, Link 2, Link 3, Link 4, and Gripper as the subassemblies.

  • Assemble the Leader Arm

    Assemble the leader arm. The document marks the specific assembly instructions as TODO and provides no part sequence or other assembly details.

  • Assemble the arm

    Assemble the arm according to the assembly guide only after all motors have been configured and verified.

  • Assemble the AIRA Core Kit

    Assemble the verified parts kit using the assembly guide included with it. The document states that assembly can be completed in an afternoon.

Software

  • Use native LeRobot plugins

    Use LeRobot's plugin architecture rather than a fork. ACT, Diffusion Policy, PI0, and GR00T N1.5 are supported out of the box.

  • Install the software

    Clone the Nextis-AIRA-3D repository, change into its directory, and install the package with pip.

  • Set up the CAN bus

    Run the CAN bus setup command.

  • Configure the CAN interface

    Plug in the USB-CAN adapter, then run the CAN setup command with administrator privileges.

  • Resolve CAN bus permission errors

    Run the setup with `sudo`, or add the user to the `can` group.

  • Check the Dynamixel motor bus connection

    List the available USB serial devices and check the USB port used by DynamixelMotorsBus.

Calibrate and test

  • Configure and Test Every Motor Individually

    Before assembling the arm, configure and test every motor individually. During the first tests, always keep one hand on the power switch.

  • Configure each motor

    Run `aira-setup` and configure the motors one by one through the setup wizard. The wizard requires no terminal expertise.

  • Enable compliant position tracking

    Use MIT Impedance Control on the follower for compliant position tracking and smooth, safe operation. Force feedback is planned.

  • Configure the motors

    Before installing the motors in the arm, configure each one individually on the bench and calibrate it. The wizard guides you through connecting each motor, setting Slave/Master IDs, and calibrating.

  • Check the unresponsive motor

    Check the power-supply voltage, CAN bus wiring, and termination resistor.

  • Re-run the robot calibration

    Delete the saved calibration cache directory, then re-run the AIRA setup command.

  • Configure and test each motor

    Configure and test every Damiao J8009P motor individually before assembly. Check CAN IDs, Master/Slave IDs, and control parameters; never power an assembled arm with unconfigured motors.

  • Bench Test the Motors

    Connect all follower motors to the CAN bus simultaneously and run the test. All 7 motors should report their positions; check wiring and ID configuration for any motor that does not respond.

  • Power On Both Arms

    Power the follower arm with 24V and the leader arm with 5V for the final integration test.

  • Read All Motor Positions

    Run a quick position read to confirm that all motors respond.

  • Perform AIRA Core Self-Calibration

    Perform the required self-calibration after assembly.

Data and training

  • Teleoperate and run an autonomous policy

    Teleoperate using the leader arm, then execute an autonomous policy. The demonstration moves from leader-arm teleoperation to autonomous policy execution.

  • Teleoperate the robot

    Run teleoperation with the aira_follower robot and aira_leader teleoperator.

  • Record demonstrations

    Record the pick-up-the-red-block task with aira_follower and aira_leader, saving the dataset to your-username/pick-and-place.

  • Train a policy

    Train a policy using the act policy and the pick-and-place dataset.

  • Start Teleoperation at Low Gains

    Start teleoperation at low gains first. On the first use, keep one hand on the power switch and cut power immediately if the arm moves unexpectedly.

Use it

  • Deploy the policy

    Run evaluation on the aira_follower robot using the last act_pick_and_place checkpoint from training.

  • Run AIRA teleoperation

    Run the LeRobot teleoperation command with the `aira_follower` robot type; LeRobot automatically discovers `lerobot_robot_aira` and `lerobot_teleoperator_aira`, with no source-code changes required.

Documents