Connecting to sources…

How to build Poppy Ergo Jr

36 steps to build Poppy Ergo Jr, with the source documents.

Poppy Ergo Jr is a low-cost six-degree-of-freedom robot arm with a modular 3D-printed design and Dynamixel XL-320 motors. The repository provides printable mechanical parts, a bill of materials, and a link to assembly instructions.

Buy parts

  • Buy the Pixl control board

    Buy 1 Pixl board to control XL320 motors.

  • Buy six XL-320 motors

    Buy 6 Robotis dynamixel XL-320 motors.

  • Buy the OLLO rivet set

    Buy one set of OLLO rivets containing about 70 colored and 4 grey rivets.

  • Buy the OLLO TOOL

    Buy one OLLO TOOL.

  • Buy the Raspberry Pi mounting screws

    Buy four M2.5x6mm screws for fixing the Raspberry Pi on the base.

  • Buy the camera mounting screws

    Buy four M2x5mm screws for fixing the camera.

  • Buy the camera fixing nuts

    Buy four M2 nuts for fixing the camera.

  • Buy the M2.5 standoff

    Buy one 10mm Male/Female M2.5 standoff.

  • Buy Raspberry Pi 2 or 3

    Buy one Raspberry Pi 2 or Raspberry Pi 3.

  • Buy an 8GB microSD card

    Buy one 8GB microSD card.

  • Buy the Raspberry Pi camera

    Buy one Raspberry Pi camera.

  • Buy the specified AC power supply

    Buy one 7.5V, 2A AC power supply with a 2.1 x 5.5 x 9.5mm jack connector; the document also provides an RS Online power-supply link.

  • Buy a short Ethernet cable

    Buy one short Ethernet cable.

  • Check the BOM and suppliers

    The document points to the full bill of materials in doc/bom.md and the supplier list in doc/suppliers.md.

Print and make

  • Make the disk_support disk

    Laser-cut 1 disk_support.stl, or 3D-print it instead, which takes a lot of time.

  • Print the base

    3D-print 1 base.stl from the STL file.

  • Print the horn2horn parts

    3D-print 3 horn2horn.stl files.

  • Print the side2side parts

    3D-print 3 side2side.stl files.

  • Print the long U part

    3D-print 1 long_U.stl from the STL file.

  • Print the short U part

    3D-print 1 short_U.stl from the STL file.

  • Print the camera support

    3D-print 1 support_camera.stl from the STL file.

  • Print the lamp tool

    3D-print 1 lamp.stl from the tool STL file.

  • Print the gripper fixation

    3D-print 1 gripper-fixation.stl from the tool STL file.

  • Print the gripper fixed part

    3D-print 1 gripper-fixed_part.stl from the tool STL file.

  • Print the gripper rotative part

    3D-print 1 gripper-rotative_part.stl from the tool STL file.

  • Print the pen holder

    3D-print 1 pen-holder.stl from the tool STL file.

  • Print the pen screw

    3D-print 1 pen-screw.stl from the tool STL file.

  • Download Printable STL Files

    Download the STL files from the last GitHub release to print the Poppy Ergo Jr shapes.

  • View the Current Onshape Design

    Use a free Onshape public-project account to open the hardware project and view or modify its parts.

  • Get the Legacy OpenScad Files

    Get the OpenScad hardware version from the design-with-openSCAD directory; it is kept for memory and educational example and is no longer maintained.

  • Get the Thingiverse Community Version

    Find the alternative hardware version made by S. Brunel on Thingiverse.

  • Review mechanical and electronics parts in hardware folder

    The hardware folder contains the mechanical and electronics parts.

Software

  • Expand the SD Card Root Partition

    Make sure the SD card has at least 8GB of space; run the provided raspi-config command if the partition needs expansion.

  • Reboot the Raspberry Pi

    Reboot the Raspberry Pi after expanding the root partition.

  • Run the Raspoppy Installation Script

    Run the installation script on a Raspbian-based Raspberry Pi. The Raspoppy scripts install custom Python, configure serial communication and the web interface, and create a Poppy user.

Use it

  • Browse the code samples for ideas

    Once the robot is ready to use, look at the code samples in the software/samples folder for ideas.

Common problems

  • Truncated or invalid project files make 3D models unusable for slicing #35 #55 #67 #52
  • The system image lacks dependencies required for camera and ROS #63 #62
  • Motor configuration or robot initialization cannot connect to the motor controller #36 #48 #64
  • The motor-reading block is incompatible with the all-motors block #23
  • Robot motion lags and wireless connectivity slows after installation #49 #57
  • The official image fails to boot on some Raspberry Pi versions #50 #56
  • The installation script fails to complete default-user setup #58
  • Capture on the test page returns an internal server error #61

Documents