Connecting to sources…

How to build GrowBot: the whole process

35 steps to build GrowBot, from buying parts, printing and assembly to software, calibration and training, with the bill of materials, shop links and the official source…

GrowBot is an AI creature whose brain runs on a phone mounted to a small biped robot body, allowing it to sense, move, and remember its surroundings. The repository provides printable body files, a bill of materials, a build guide, and firmware instructions for making and running the robot.

Bill of materials · Parts

PartQty
Raspberry Pi Pico 2 W · RP2350, Wi-Fi, headers already soldered1
MG90S micro servo · metal gear, 9 g, standard 180°2
Waveshare Pico Servo Driver · Pico carrier with servo sockets, screw terminal and power switch1
AA batteries · 1.5 V, rechargeable lithium recommended4
4×AA battery holder · low profile, no cover, bare wire ends1
Double-sided foam tape1 roll

Buy parts

  • Buy the standard GrowBot parts

    The standard build needs a Pico, two servo legs, AA batteries, and a phone for the brain.

  • Prepare two small screwdrivers

    Prepare a small Phillips screwdriver for the servo screws and a tiny flat-head screwdriver for the battery terminal.

Print and make

  • Print two leg parts

    Print two `growbot_diy_leg_v1_r01.stl` parts in plain PLA with no supports.

  • Print the robot body

    Print `growbot_diy_body_v1.1_r01_beta_01.stl` in plain PLA with no supports.

  • Print the backplate

    Print `growbot_diy_backplate_v1_r01.stl` in plain PLA with no supports.

  • Make parts from the cutout template

    Without a printer, print the cutout template at 100% on paper and build the parts from any stiff material.

Assemble

  • Mount the Pico

    Push the Pico into the Waveshare Pico Servo Driver with the USB ends matching.

  • Connect the servos

    Put the left servo in socket 0 and the right servo in socket 1. Connect brown to G, red to V, and yellow or orange to S.

  • Connect the battery

    In the board's screw terminal, connect battery-holder red to + (VIN) and black to GND, never to the Pico's own pins. The servos use the battery pack; USB alone will not move them.

  • Use a Kitronik 5329

    The Kitronik Robotics Board 5329 also works, but it uses different sockets. See “want to use another board?” in the full guide for this alternative.

  • Mount the phone

    Secure the phone with foam tape or an elastic band, with the screen facing out, the camera at the top, and away from the batteries.

  • Assemble without soldering

    The standard GrowBot build requires no soldering.

  • Connect servos and battery

    Connect the left servo to socket 0 and the right servo to socket 1 on the Waveshare, then connect the battery to the screw terminal.

  • Attach legs to servo horns

    Screw the printed legs onto the servo horns; do not use glue.

Software

  • Install with the build page

    Open step 02 of growbot.dev/build in Chrome or Edge on a computer. It installs all of the chip software over USB and saves your Wi-Fi.

  • Install the Pico MicroPython firmware

    Hold BOOTSEL while plugging in the Pico, then drag `micropython-pico2w.uf2` onto the `RP2350` drive.

  • Create the Wi-Fi secrets file

    Copy `secrets.example.py` to `secrets.py` and enter your Wi-Fi details. The Pico only joins 2.4 GHz Wi-Fi.

  • Install the remote-copy tool

    Run `pip install mpremote`, then perform the following copy commands from the firmware folder.

  • Copy the firmware files

    Copy `PicoRobotics.py`, `act_engine.py`, `secrets.py`, and `relay_chip.py` to the Pico. The first three keep their filenames, while `relay_chip.py` becomes `main.py`.

  • Reset the Pico and open the REPL

    Reset the Pico with `mpremote reset`, then start the MicroPython REPL with `mpremote repl`.

  • Pair the robot

    Note the printed `PAIRING CODE: gb-xxxxxx`. Pair the robot using step 4 of `BUILD.md`.

  • Enable travel Wi-Fi setup

    Use the build page if you want travel Wi-Fi. Its installer creates the setup-network password and hands it to your phone.

  • Adapt the motor controls

    Change only `board.servoWrite(port, deg)` and `board.release(port)` to match your hardware. Port 1 is the left motor and port 3 is the right motor.

  • Install MicroPython

    Hold BOOTSEL while plugging the Pico into USB. The RP2350 drive appears; drag micropython-pico2w.uf2 onto it.

  • Configure Wi-Fi credentials

    Copy secrets.example.py to secrets.py and enter the Wi-Fi name and password. The Pico only joins 2.4 GHz Wi-Fi.

  • Install mpremote

    Install mpremote, then run the file-copy commands from the firmware folder.

  • Copy firmware files

    From the firmware folder, copy PicoRobotics.py, act_engine.py, and secrets.py to the Pico.

  • Reset and open REPL

    Reset the Pico and open its interactive REPL.

  • Record the pairing code

    Write down the printed “PAIRING CODE: gb-xxxxxx”. It is needed in step 4.

  • Save files with Thonny

    Without a terminal, open each file in Thonny and choose File > Save As > Raspberry Pi Pico. Save relay_chip.py as main.py.

  • Open and bookmark the control page

    Open `growbot.dev/v3/next.html?id=<your code>&mode=legs` on the phone and bookmark it. Step 09 of the build guide provides a QR code that does this and brings along your leg trim.

Calibrate and test

  • Provide adequate servo power

    The servos need 5 to 6 V, and their current can spike above 2 A when they push hard.

  • Use four fresh matching cells

    Use four fresh or fully charged cells of the same kind to prevent leg twitching and Pico resets caused by a weak supply.

  • Straighten the legs

    If the legs look uneven, use step 07 (trim) of the build guide to straighten them.

  • Run the power-on movement check

    At power-on, the chip runs a short movement check on both outputs. On a wheeled build, keep the wheels off the ground during the check.

Documents