Connecting to sources…

How to build AKARI (small desktop AI camera robot)

54 steps to build AKARI (small desktop AI camera robot), with the source documents.

No sales and no official kit were found. The manual's parts lists give shop links and quantities but no prices or total; it says only that AKARI Light costs about half as much up front as AKARI

Buy parts

  • Check AKARI setup requirements
  • Prepare the M5stack board

    Prepare 1 M5stack board.

  • Prepare the AKARI Head

    Prepare 1 AKARI Head.

  • Prepare the AKARI Body

    Prepare 1 AKARI Body.

  • Prepare the AKARI Cover

    Prepare 1 AKARI Cover.

  • Prepare the AKARI Base

    Prepare 1 AKARI Base.

  • Prepare the AKARI Plate

    Prepare 1 AKARI Plate.

  • Buy the Lattepanda Alpha

    Buy 1 Lattepanda Alpha, model Lattepanda Alpha 864S DFR0546.

  • Buy the M5Stack BASIC

    Buy 1 M5Stack BASIC, model M5Stack BASIC V2.7.

  • Buy the temperature, humidity and pressure sensor

    Buy 1 temperature, humidity and pressure sensor unit ENVⅢ, model M5STACK-U001-C; ENVⅣ can also be used.

  • Buy the light sensor unit

    Buy 1 light sensor unit, model M5STACK-LIGHT-UNIT.

  • Buy a 2.1mm DC jack

    Buy one board-mounted 2.1mm standard DC jack (4A), model MJ-179PH.

  • Buy a 4P PH connector

    Buy one top-entry PH connector with base, model B4B-PH-K-S.

  • Buy a 3P EH connector

    Buy two top-entry EH connectors, model B3B-EH-A. Choose either 13-A or 13-B.

  • Buy a 1×3 pin header

    Buy two 2mm-pitch 1×3 pin headers, model PH2-1x3SBG. Choose either 13-A or 13-B.

  • Buy a 20P box header

    Buy one 20P box header, model BH-20SG.

  • Buy a DC-DC converter

    Buy one DC-DC converter, model M78AR05-1.

  • Buy 10μF ceramic capacitors

    Buy two multilayer ceramic capacitors rated at 10μF, model RD20F106Z1EH5L.

  • Buy a 2P terminal block

    Buy one 2P terminal block, model TB-111-2.

  • Buy a 20P IDC ribbon cable

    Buy one 2×10 (20P) IDC ribbon cable with connectors on both ends, model DG01032-0041-01-180mm.

  • Buy a 12V 5A AC adapter

    Buy one 12V 5A AC adapter, model ATS065-P120.

  • Buy 4P PH connector cable

    Buy the red, black, yellow, and green 4P PH connector cable, model DG01032-0049-01, from Aki.

  • Buy panel-mount DC jack

    Buy the 2.1 mm standard panel-mount DC jack, model C-17108, from Aki.

  • Buy red 26AWG Teflon wire

    Buy the red 26AWG Teflon-insulated wire, 10 cm long, from Aki.

  • Buy OAK-D Lite camera

    Buy the OAK-D Lite OAK-D-LITE OpenCV DepthAI camera from Switch Science or Mouser.

  • Buy M5Stack header and socket set

    Buy the 2×15 pin-header and socket set for M5Stack from Switch Science.

  • Buy top-entry Grove connectors

    Buy the top-entry Grove connectors from Switch Science.

  • Buy Dynamixel XL430 motor

    Buy the Dynamixel 2XL430-W250-T, model BTX079, from Best Technology.

  • Buy HN11-I101 set

    Buy the HN11-I101 Set, model BTX098, from Best Technology.

  • Buy USB2DXIF interface

    Buy the USB2DXIF, model BTE101, from Best Technology.

  • Buy X3P robot cable

    Buy the 180 mm Robot Cable-X3P, model BTX104, from Best Technology.

Assemble

  • Mount the M5 board

    Mount the M5 board on the body following the assembly animation, with the CN9 pin header at the front right.

  • Mount the environmental sensor unit

    Mount the temperature, humidity, and pressure sensor unit following the assembly animation, with the ENVⅢ label facing inward.

  • Mount the light sensor unit

    Mount the light sensor unit following the assembly animation, with the light sensor label facing inward.

  • Join the head and body

    Join the head and body following the assembly animation.

  • Install the Power Switch

    Fit the power switch into the body with the circle mark facing downward.

  • Install the DC Jack

    Install the DC power jack in the body following the assembly animation.

  • Solder the DC Jack Wires

    Solder the red-and-black wire to the positive terminal, which is shorter, and the yellow-and-green wire to the negative terminal, which is longer.

  • Install the M5Stack

    Mount the M5Stack in the body following the assembly animation.

  • Connect the GPIO Cable

    Connect the GPIO cable at the designated location.

  • Connect the USB2DXIF

    Connect the USB2DXIF to the board-side connector. If the (13-B) 2mm-pitch 1×3 pin header is used, connect it in the same orientation as shown in the figure.

  • Connect the M5Stack USB

    Complete the M5Stack USB connection as shown in the diagrams.

  • Connect the motor wires

    Connect the motor wires as shown in the diagrams. If the (13-B) 2mm-pitch 1×3 pin header is used, connect them in the same orientation as shown in the figure.

  • Install the cover

    Install the cover by following the assembly animation and diagrams.

  • Mount the USB hub

    Mount the USB hub by following the assembly animation and diagrams.

  • Connect to the USB hub

    Connect the USB to the USB hub as shown in the diagrams.

  • Connect the Dynamixel Motor

    Connect the included cable to the ID(B) port of the Dynamixel 2XL430-W250-T; either end of the cable may be inserted first.

  • Mount the OAK-D on the Head

    Mount the OAK-D on the AKARI head following the assembly animation.

  • Mount the Dynamixel on the Head

    Mount the Dynamixel on the AKARI head following the assembly animation.

  • Attach the magnets

    Attach the magnets to the head by following the assembly animation.

  • Install the ribbon cable

    Install the ribbon cable inside the head by following the assembly animation.

  • Install the left-angle USB panel cable

    Pass the 30 cm left-angle panel-mount USB 3.0 cable through the back of the head. Install the connector so that the blue plate inside the terminal faces outside the head.

  • Connect the OAK-D Lite USB

    Connect the OAK-D Lite to the installed USB connection.

Calibrate and test

  • Check the robot's range of motion

    Check the robot's range of motion.

Common problems

  • Locating pins exceed PCB holes, causing tilted header soldering #3
  • Head interferes with ring, preventing contact with Dynamixel #8
  • PCB data contains artwork errors and reversed pin assignments #9 #11
  • Connector tapping screw protrudes through thin printed head part #12

Parts

  • LattePanda Alpha 864s (Intel Core m3‑8100Y, 8 GB RAM, 64 GB eMMC) running Ubuntu 24.04
  • One Dynamixel 2XL430‑W250‑T two-axis servo module (1.4 N·m at 11.1 V), with an HN11‑I101 bracket set, USB2DXIF interface and Robot Cable‑X3P
  • OAK‑D Lite AI camera (head)
  • M5Stack BASIC V2.7 on a custom M5Stack board (Gerbers published, parts soldered by hand), plus M5Stack ENV III and light sensor units
  • 12 V 5 A power adapter, DC‑DC converter, 4-port USB hub, USB and DC cables, a small rocker switch, 2 magnets
  • 5 printed parts: Head, Body, Cover, Base, Plate (STL/STEP); AKARI Light swaps in a Raspberry Pi 5 (8 GB), 2 Feetech STS3215 servos and a 5 V 6.2 A supply

Tools

  • Precision and No. 2 Phillips screwdrivers, soldering iron and solder, nippers, scissors
  • A 3D printer (the manual uses FlashForge as its example), or printing ordered from JLCPCB or similar
  • For setup: a PC, display, keyboard, mouse, USB stick of 8 GB or more, a USB hub with 3+ ports and a microSD reader

Skills

  • Soldering the M5Stack board's components and connectors
  • Installing Ubuntu 24.04 on the LattePanda, setting up the AKARI environment with Ansible and preparing the M5Stack's SD card
  • Python and JupyterLab, with optional Scratch, ROS 2 Jazzy and custom YOLO training

Software

  • akari_software: the akari_client Python SDK (joints and M5Stack control) and the web console (JupyterLab, web controller, services, projects)
  • Sample apps: face tracking, YOLO object detection and 3D tracking, hand tracking, ChatGPT / Claude / Gemini voice chat, RAG chat, local-VLM behaviour captioning and more
  • Scratch 3.0 extensions, the akari_ros ROS 2 Jazzy packages, an MCP server, the akari_practice Python exercises and a custom object-detection training workflow

Documents